ASTM D 7220 : 2012 : R2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry
Available format(s)
Hardcopy , PDF
Superseded date
12-02-2022
Language(s)
English
Published date
07-10-2017
CONTAINED IN VOL. 05.04, 2017 Defines an energy-dispersive X-ray fluorescence (EDXRF) method for the determination of total sulfur in automotive, No. 2 heating, and jet fuels with a concentration range of 3 to 942 mg/kg.
1.1This test method specifies an energy-dispersive X-ray fluorescence (EDXRF) method for the determination of total sulfur in automotive, No. 2 heating, and jet fuels with a concentration range of 3 mg/kg to 942 mg/kg.
1.1.1The pooled limit of quantitation of this test method as obtained by statistical analysis of inter laboratory test results is 3 mg/kg sulfur.
1.1.2This test method is applicable to gasoline, oxygen enriched gasoline (RFG), diesel, diesel/biodiesel blends containing up to twenty volume percent biodiesel, kerosene, jet fuel, jet fuel/biodiesel blends containing up to five volume percent biodiesel and No. 2 home heating oil.
1.2A fundamental assumption in this test method is that the standard and sample matrix is well matched. Matrix mismatch can be caused by C/H ratio differences between samples and standards or by the presence of other heteroatoms.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3.1The preferred concentration units are mg/kg sulfur.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 7455 : 2019 | Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis |
| ASTM D 7578 : 2018 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM D 7343 : 2018 | Standard Practice for Optimization, Sample Handling, Calibration, and Validation of X-ray Fluorescence Spectrometry Methods for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM D 8076 : 2018 | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
| ASTM D 396 : 2019 | Standard Specification for Fuel Oils |
| ASTM D 7826 : 2019 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
| ASTM D 6227 : 2018 | Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component |
| ASTM D 7547 : 2018 : REV A | Standard Specification for Hydrocarbon Unleaded Aviation Gasoline |
| ASTM D 4814 : 2019 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 3699 : 2018 : REV A | Standard Specification for Kerosine |
| ASTM D 7960 : 2018 | Standard Specification for Unleaded Aviation Gasoline Test Fuel Containing Non-hydrocarbon Components |
| ASTM D 7467 : 2019 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 7719 : 2018 | Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline |
| ASTM D 3699 : 2019 | Standard Specification for Kerosine |
| ASTM D 7343 : 2020 | Standard Practice for Optimization, Sample Handling, Calibration, and Validation of X-ray Fluorescence Spectrometry Methods for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM D 7578 : 2020 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM D 8011 : 2019 | Standard Specification for Natural Gasoline as a Blendstock in Ethanol Fuel Blends or as a Denaturant for Fuel Ethanol |
| ASTM D 7467 : 2020 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
| ASTM D 2880 : 2020 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 7547 : 2021 | Standard Specification for Hydrocarbon Unleaded Aviation Gasoline |
| ASTM D 7960 : 2021 | Standard Specification for Unleaded Aviation Gasoline Test Fuel Containing Non-hydrocarbon Components |
| ASTM D 7719 : 2021 : REV A | Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline Test Fuel |
| ASTM D 8076 : 2021 : REV B | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
| ASTM D 7826 : 2021 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
| ASTM D 8275 : 2022 | Standard Specification for Gasoline-like Test Fuel for Compression-Ignition Engines |
| ASTM D 975 : 2022 | Standard Specification for Diesel Fuel |
| ASTM D 4814 : 2022 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
| ASTM D 8110 : 2017 | Standard Test Method for Elemental Analysis of Distillate Products by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2020 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6300 : 2013 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4057 : 1995 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2010 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6300 : 2014 : REV A : EDT 1 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6299 : 2013 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM D 6299 : 2017 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2017 : REV B | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6300 : 2017 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6299 : 2009 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 1995 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2017 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2013 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2021 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM D 6299 : 2010 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2022 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6300 : 2016 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2004 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2019 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2021 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6300 : 2019 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2020 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 6299 : 2000 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2010 : EDT 2 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2016 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 2015 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2019 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6300 : 2020 : REV B | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2000 : REV A | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6300 : 2006 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2014 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2015 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 1999 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4177 : 2022 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2020 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 1995 : R2010 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2008 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 1995 : R2000 | Standard Practice for Automatic Sampling of Peroleum and Petroleum Products |
| ASTM D 6300 : 2013 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6299 : 2002 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6300 : 2008 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2003 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6300 : 2007 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6299 : 2022 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6300 : 2002 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 2016 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 2020 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 1995 : R2005 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2016 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 6299 : 2007 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2007 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2020 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2017 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 2015 : REV A | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6300 : 2014 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
| ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2002 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.