• ASTM D 7470 : 2008 : R2015

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Practice for Evaluating Elevated Temperature Performance of End-Jointed Lumber Studs

    Available format(s):  Hardcopy, PDF

    Superseded date:  08-20-2021

    Language(s):  English

    Published date:  06-04-2015

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 04.10, 2015 Describes the elevated temperature performance of end-jointed lumber studs.

    Scope - (Show below) - (Hide below)

    1.1This practice is to be used to evaluate the elevated temperature performance of end-jointed lumber studs.

    1.2A symmetric wall assembly containing end-jointed lumber studs is exposed to a standard fire exposure specified in Test Methods E119.

    1.3End-jointed lumber studs are deemed qualified if the wall assembly resists a standard fire exposure specified in Test Methods E119 for a period of 60 min or more. Qualification of end-jointed lumber studs are restricted to the joint configuration and adhesive tested.

    1.4This practice is used to evaluate the performance of end-jointed lumber studs to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment under actual fire conditions.

    1.5The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

    1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee D 07
    Document Type Standard Practice
    Product Note Reconfirmed 2015
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM F 1667 : 2005 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM D 6513 : 2014 Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests
    ASTM D 4688 : 1999 : R2013 Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber
    ASTM F 1667 : 2018 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM D 6513 : 2000 Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Endurance Tests
    ASTM F 1667 : 2013 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2011 : REV A Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2011 : REV A : EDT 1 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2015 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2021 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2010 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM D 4688 : 1999 Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber
    ASTM F 1667 : 2018 : REV A Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM D 6513 : 2014 : REDLINE Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests
    ASTM C 1396/C1396M : 2017 : REDLINE Standard Specification for Gypsum Board
    ASTM D 4688 : 1999 : R2005 Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber
    ASTM F 1667 : 2000 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2003 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2020 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2001 : REV A Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2011 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM F 1667 : 2002 : REV A Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM D 6513 : 2000 : R2005 Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Endurance Tests
    ASTM D 6513 : 2021 Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests
    ASTM F 1667 : 2017 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM E 119 : 2007 Standard Test Methods for Fire Tests of Building Construction and Materials
    ASTM F 1667 : 2002 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
    ASTM D 6513 : 2008 Standard Practice for Calculating the Superimposed Load on Wood-frame Walls for Standard Fire-Resistance Tests
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective