• There are no items in your cart

ASTM D 75/D75M : 2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Sampling Aggregates
Available format(s)

Hardcopy , PDF

Superseded date

11-12-2019

Language(s)

English

Published date

06-19-2014

This practice covers sampling of coarse and fine aggregates for the following purposes:

Preliminary investigation of the potential source of supply.

1.1This practice covers sampling of coarse and fine aggregates for the following purposes:

1.1.1Preliminary investigation of the potential source of supply,

1.1.2Control of the product at the source of supply,

1.1.3Control of the operations at the site of use, and

1.1.4Acceptance or rejection of the materials.

Note 1Sampling plans and acceptance and control tests vary with the type of construction in which the material is used.

1.2The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 2The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Practice D3666 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3666 alone does not completely assure reliable results. Reliable results depend on many factors; following the suggestions of Practice D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.

Committee
D 04
DocumentType
Standard Practice
Pages
8
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 404 : 2018 Standard Specification for Aggregates for Masonry Grout
ASTM C 1777 : 2020 Standard Test Method for Rapid Determination of the Methylene Blue Value for Fine Aggregate or Mineral Filler Using a Colorimeter
ASTM C 586 : 2019 Standard Test Method for Potential Alkali Reactivity of Carbonate Rocks as Concrete Aggregates (Rock-Cylinder Method)
ASTM D 6825 : 2021 Standard Guide for Placement of Riprap Revetments
ASTM D 448 : 2012 : R2022 Standard Classification for Sizes of Aggregate for Road and Bridge Construction
ASTM C 87/C87M : 2017 Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar
ASTM C 33/C33M : 2018 Standard Specification for Concrete Aggregates
ASTM C 1451 : 2018 Standard Practice for Determining Variability of Concrete-Making Materials From a Single Source
ASTM D 1864/D1864M : 1989 : R2017 Standard Test Method for Moisture in Mineral Aggregate Used on Built-Up Roofs
ASTM D 5284 : 2009 : R2017 Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid
ASTM C 40/C40M : 2020 Standard Test Method for Organic Impurities in Fine Aggregates for Concrete
ASTM D 5744 : 2018 Standard Test Method for Laboratory Weathering of Solid Materials Using a Humidity Cell
ASTM C 1293 : 2020 : REV A Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction
ASTM D 7196 : 2018 Standard Test Method for Raveling Test of Cold-Mixed Emulsified Asphalt Samples
ASTM D 5013 : 2018 Standard Practices for Sampling Wastes from Pipes and Other Point Discharges
ASTM C 494/C494M : 2019 : EDT 1 Standard Specification for Chemical Admixtures for Concrete
ASTM D 2940/D2940M : 2020 Standard Specification for Graded Aggregate Material for Bases or Subbases for Highways or Airports
ASTM C 897 : 2015 : R2020 Standard Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters
ASTM C 295/C295M : 2019 Standard Guide for Petrographic Examination of Aggregates for Concrete
ASTM C 233/C233M : 2018 Standard Test Method for Air-Entraining Admixtures for Concrete
ASTM D 6704 : 2022 Standard Test Method for Determining the Workability of Asphalt Cold Mix Patching Material
ASTM D 8237 : 2021 Standard Test Method for Determining Fatigue Failure of Asphalt-Aggregate Mixtures with the Four-Point Beam Fatigue Device
ASTM C 332 : 2017 Standard Specification for Lightweight Aggregates for Insulating Concrete
ASTM D 1139/D1139M : 2022 Standard Specification for Aggregate for Single or Multiple Asphalt Surface Treatments
ASTM D 8021 : 2020 Standard Guide for Blast Furnace and Steel Furnace Slag as Produced During the Manufacture of Iron and Steel
ASTM D 6932/D6932M : 2021 Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Asphalt Mixtures
ASTM D 7762 : 2018 : EDT 1 Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash
ASTM D 1865/D1865M : 2009 : R2017 Standard Test Method for Hardness of Mineral Aggregate Used on Built-Up Roofs
ASTM E 2788/E2788M : 2018 Standard Specification for Use of Expanded Shale, Clay and Slate (ESCS) as a Mineral Component in the Growing Media and the Drainage Layer for Vegetative (Green) Roof Systems
ASTM D 3987 : 2012 : R2020 Standard Practice for Shake Extraction of Solid Waste with Water
ASTM D 692/D692M : 2020 Standard Specification for Coarse Aggregate for Asphalt Paving Mixtures
ASTM C 330/C330M : 2017 : REV A Standard Specification for Lightweight Aggregates for Structural Concrete
ASTM C 535 : 2016 Standard Test Method for Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine
ASTM D 4215 : 2021 Standard Specification for Cold-Mixed, Cold-Laid Asphalt Paving Mixtures
ASTM D 6234 : 2013 : R2020 Standard Test Method for Shake Extraction of Mining Waste by the Synthetic Precipitation Leaching Procedure
ASTM D 8262 : 2022 Standard Test Method for Determining the pH of Granular Material for Use in Embankments, Subgrades, and Retaining Wall Backfil
ASTM C 1077 : 2017 Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation
ASTM C 1761/C1761M : 2017 Standard Specification for Lightweight Aggregate for Internal Curing of Concrete
ASTM D 8378/D8378M : 2021 Standard Test Method for Potential Expansion of Steel Slag from Hydration Reactions by Autoclave
ASTM D 8038 : 2016 : R2022 : EDT 1 Standard Practice for Reclamation of Recycled Aggregate Base (RAB) Material
ASTM E 1109 : 2019 Standard Test Method for Determining the Bulk Density of Solid Waste Fractions
ASTM D 7370/D7370M : 2014 : R2021 Standard Test Method for Determination of Relative Density and Absorption of Fine, Coarse, and Blended Aggregate Using Combined Vacuum Saturation and Rapid Submersion
ASTM D 2419 : 2022 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
ASTM D 4793 : 2009 : R2017 Standard Test Method for Sequential Batch Extraction of Waste with Water
ASTM D 8012 : 2018 Standard Practice for Reclamation of Scrap and Waste Asphalt Shingles to Produce Reclaimed Asphalt Shingles (RAS) for Use in Transportation Applications
ASTM C 29/C29M : 2017 : REV A Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate
ASTM D 6307 : 2019 Standard Test Method for Asphalt Content of Asphalt Mixture by Ignition Method
ASTM C 88/C88M : 2018 Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate
ASTM D 7655/D7655M : 2012 : R2022 Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems
ASTM C 566 : 2019 Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying
ASTM C 641 : 2017 Standard Test Method for Iron Staining Materials in Lightweight Concrete Aggregates
ASTM D 4125/D4125M : 2021 Standard Test Methods for Asphalt Content of Asphalt Mixtures by the Nuclear Method
ASTM D 3744/D3744M : 2018 Standard Test Method for Aggregate Durability Index
ASTM D 8155 : 2017 Standard Practice for Shake Extraction of Solid Mining and Metallurgical Processing Waste with Water
ASTM D 4791 : 2019 Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate
ASTM C 1356 : 2007 : R2020 Standard Test Method for Quantitative Determination of Phases in Portland Cement Clinker by Microscopical Point-Count Procedure
ASTM E 889 : 1982 : R2023 Standard Test Method for Composition or Purity of a Solid Waste Materials Stream
ASTM C 35 : 2001(R2019) Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster
ASTM D 5081/D5081M : 1990 : R2018 Standard Test Method for Aggregate Layer Hiding Power
ASTM D 1073 : 2016 : R2022 Standard Specification for Fine Aggregate for Asphalt Paving Mixtures
ASTM D 7000 : 2019 : REV A Standard Test Method for Sweep Test of Emulsified Asphalt Surface Treatment Samples
ASTM F 2980 : 2013 : R2017 Standard Test Method for Analysis of Heavy Metals in Glass by Field Portable X-Ray Fluorescence (XRF)
ASTM C 144 : 2018 Standard Specification for Aggregate for Masonry Mortar
ASTM D 5106 : 2022 Standard Specification for Steel Slag Aggregates for Asphalt Paving Mixtures
ASTM D 420 : 2018 Standard Guide for Site Characterization for Engineering Design and Construction Purposes
ASTM D 6155 : 2019 Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures
ASTM D 4792/D4792M : 2013 : R2019 Standard Test Method for Potential Expansion of Aggregates from Hydration Reactions
ASTM C 1797 : 2017 Standard Specification for Ground Calcium Carbonate and Aggregate Mineral Fillers for use in Hydraulic Cement Concrete
ASTM D 5233 : 1992 : R2017 Standard Test Method for Single Batch Extraction Method for Wastes
ASTM D 1863/D1863M : 2005 : R2018 Standard Specification for Mineral Aggregate Used on Built-Up Roofs
ASTM F 2797 : 2019 Standard Test Method for Evaluating Edge Cleaning Effectiveness of Vacuum Cleaners
ASTM D 8249 : 2019 Standard Practice for Use of Rotary Kiln Produced Porous Ceramic as a Mineral Amendment in Topsoil Used for Landscaping and Related Purposes
AWWA C104/A21.4:2022 Cement–Mortar Lining for Ductile-Iron Pipe and Fittings

ASTM D 3666 : 2013 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2011 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2007 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3665 : 2002 Standard Practice for Random Sampling of Construction Materials
ASTM D 3666 : 2009 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3665 : 2012 : R2017 Standard Practice for Random Sampling of Construction Materials
ASTM D 3665 : 2007 Standard Practice for Random Sampling of Construction Materials
ASTM D 3666 : 2005 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2003 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2000 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3665 : 2012 Standard Practice for Random Sampling of Construction Materials
ASTM D 3666 : 2007 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2007 : EDT 2 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2016 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2003 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2001 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2006 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3665 : 2007 : EDT 1 Standard Practice for Random Sampling of Construction Materials
ASTM D 3665 : 2006 Standard Practice for Random Sampling of Construction Materials
ASTM D 3666 : 2004 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2005 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2007 : REV A : EDT 1 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3665 : 1999 Standard Practice for Random Sampling of Construction Materials
ASTM D 3666 : 2009 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2002 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.