• There are no items in your cart

ASTM D 7794 : 2021

Current
Current

The latest, up-to-date edition.

Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

04-14-2021

1.1This practice applies to the blending of automotive spark-ignition engine fuels with ethanol concentrations greater than those suitable for conventional-fuel vehicles and less than the minimum ethanol content specification limits of Specification D5798. These mid-level ethanol fuel blends are for use in flexible-fuel vehicles and are sometimes referred to at retail as “Ethanol Flex Fuel.”

1.2These mid-level ethanol fuel blends are only suitable for use in ground flexible-fuel vehicles equipped with spark-ignition engines. Flexible-fuel vehicles are designed to operate on gasoline or gasoline-ethanol blends that meet the requirements of Specification D4814, ethanol fuel blends that meet the requirements of Specification D5798, or any combination of these. In the United States, these vehicles are certified by the U.S. EPA as emissions compliant with these types of fuels.

1.3The mid-level ethanol fuel blend shall be blended from either:

1.3.1Denatured fuel ethanol conforming to the requirements of Specification D4806 with a reduced limit on inorganic chloride content that will ensure no more than 1 mg/kg inorganic chloride in the finished fuel and from spark-ignition engine fuel conforming to Specification D4814 (often at a distribution terminal or bulk plant), or

1.3.2Ethanol fuel blends conforming to Specification D5798 and from spark-ignition engine fuel conforming to Specification D4814 (often at a retail site).

1.4This practice describes the required procedures for blending various mid-level ethanol fuel blends for flexible-fuel vehicles at the bulk distribution point or retail/commercial delivery site. These requirements may be applied at other points in the production and distribution system when provided by agreement between the purchaser and the supplier.

1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Standard Practice
Pages
7
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM D 7923 : 2019 Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration

ASTM D 4057 : 2019 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4806 : 2021 Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 5191 : 2022 Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
ASTM D 7328 : 2022 Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 5798 : 2020 Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines
ASTM D 4806 : 2021 : REV A Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4815 : 2015 : REV B Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 4175 : 2020 : REV B Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 5599 : 2022 Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection
ASTM D 4815 : 2015 : REV B : R2019 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 4814 : 2024 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2022 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4815 : 2022 Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography
ASTM D 5842 : 2019 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D 5854 : 2019 Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products
ASTM D 5599 : 2018 Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection
ASTM D 7328 : 2023 Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 4814 : 2023 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2020 : REV B : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7319 : 2022 Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
ASTM D 4175 : 2022 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4814 : 2022 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2021 : REV C Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2023 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2023 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2022 : REV A : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 5501 : 2012 : R2016 Standard Test Method for Determination of Ethanol and Methanol Content in Fuels Containing Greater than 20% Ethanol by Gas Chromatography
ASTM D 7319 : 2017 Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
ASTM D 4177 : 2022 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4175 : 2023 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2023 : REV A Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2022 : EDT 1 Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 5191 : 2019 Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
ASTM D 4814 : 2021 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4057 : 2022 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 7328 : 2017 Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection
ASTM D 5842 : 2023 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D 5798 : 2021 Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines
ASTM D 4177 : 2020 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 5191 : 2020 Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method)
ASTM D 5842 : 2017 Standard Practice for Sampling and Handling of Fuels for Volatility Measurement
ASTM D 5191 : 2015 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
ASTM D 4177 : 2022 : EDT 1 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4814 : 2021 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel

View more information
US$63.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.