ASTM D 8044 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
05-26-2023
English
06-13-2017
CONTAINED IN VOL. 04.03, 2017 Defines the procedures for preparation, testing, and measurement of asphalt mixture cracking resistance at Long Term Pavement Performance (LTPP) database intermediate temperatures using semi-circular bend (SCB) geometry laboratory prepared or pavement core asphalt mix samples tested monotonically.
1.1This test method covers the procedures for preparation, testing, and measurement of asphalt mixture cracking resistance at Long Term Pavement Performance (LTPP) database intermediate temperatures using semi-circular bend (SCB) geometry laboratory prepared or pavement core asphalt mix samples tested monotonically. The SCB sample is a half-disk with a notch cut parallel to the loading and vertical axis. The test method describes the determination of the critical strain energy release rate, Jc, and other parameters determined from the load-displacement curve. These parameters can be used to rank the resistance of asphalt mixtures to cracking.
1.2The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
D 04
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM D 6373 : 2013 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 6925 : 2008 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 3666 : 2013 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2011 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM D 3666 : 2007 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6925 : 2007 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 6373 : 1999 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 6373 : 2016 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM D 3666 : 2016 : REDLINE | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6925 : 2015 : REDLINE | Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 3666 : 2009 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM E 178 : 2016 : REV A | Standard Practice for Dealing With Outlying Observations |
| ASTM E 399 : 2020 : REV A | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
| ASTM D 5361/D5361M : 2016 | Standard Practice for Sampling Compacted Asphalt Mixtures for Laboratory Testing |
| ASTM E 178 : 2021 | Standard Practice for Dealing With Outlying Observations |
| ASTM E 2309/E2309M : 2016 : REDLINE | Standard Practices for Verification of Displacement Measuring Systems and Devices Used in Material Testing Machines |
| ASTM E 178 : 2000 | Standard Practice for Dealing With Outlying Observations |
| ASTM D 6373 : 2021 : REV A | Standard Specification for Performance-Graded Asphalt Binder |
| ASTM D 3666 : 2005 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2003 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 2041/D2041M : 2011 | Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures |
| ASTM D 6925 : 2015 | Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 3666 : 2000 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 979/D979M : 2015 : REDLINE | Standard Practice for Sampling Bituminous Paving Mixtures |
| ASTM E 178 : 1994 | Standard Practice for Dealing With Outlying Observations |
| ASTM D 6925 : 2006 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM E 3029 : 2015 | Standard Practice for Determining Relative Spectral Correction Factors for Emission Signal of Fluorescence Spectrometers |
| ASTM D 979/D979M : 2015 | Standard Practice for Sampling Bituminous Paving Mixtures |
| ASTM D 3666 : 2007 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 2726/D2726M : 2021 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures |
| ASTM D 3666 : 2007 : EDT 2 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2016 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM E 4 : 2021 | Standard Practices for Force Calibration and Verification of Testing Machines |
| ASTM D 3666 : 2003 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 5361/D5361M : 2016 : REDLINE | Standard Practice for Sampling Compacted Asphalt Mixtures for Laboratory Testing |
| ASTM D 3203/D3203M : 2017 : REDLINE | Standard Test Method for Percent Air Voids in Compacted Asphalt Mixtures |
| ASTM D 5361/D5361M : 2016 : R2022 | Standard Practice for Sampling Compacted Asphalt Mixtures for Laboratory Testing |
| ASTM D 6373 : 2007 : EDT 1 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 2726/D2726M : 2014 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
| ASTM D 3666 : 2001 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6373 : 2015 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 3203/D3203M : 2017 | Standard Test Method for Percent Air Voids in Compacted Asphalt Mixtures |
| ASTM D 6925 : 2009 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 6373 : 2021 | Standard Specification for Performance-Graded Asphalt Binder |
| ASTM D 3666 : 2006 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 979/D979M : 2022 | Standard Practice for Sampling Asphalt Mixtures |
| ASTM E 399 : 2022 | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
| ASTM D 6925 : 2003 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM E 3029 : 2015 : R2023 | Standard Practice for Determining Relative Spectral Correction Factors for Emission Signal of Fluorescence Spectrometers |
| ASTM D 3666 : 2004 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| AASHTO M 332 : 2014 | SPECIFICATION FOR PERFORMANCE-GRADED ASPHALT BINDER USING MULTIPLE STRESS CREEP RECOVERY (MSCR) TEST |
| ASTM D 6373 : 2016 : REDLINE | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 6373 : 2007 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 3666 : 2005 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 2726/D2726M : 2019 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures |
| ASTM D 3666 : 2007 : REV A : EDT 1 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2009 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2002 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.