• There are no items in your cart

ASTM D 8105 : 2018

Current
Current

The latest, up-to-date edition.

Standard Guide for Use and Application of Geosynthetic Reinforcement Reduction Factor Test Results
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

07-01-2018

1.1 This guide presents a description of how to use test results from reduction factor test reports for reinforcement geosynthetics. It is based solely on testing and reporting requirements as established in American Association of State Highway and Transportation Officials (AASHTO) standard AASHTO R 69-15, Standard Practice for Determination of Long-Term Strength for Geosynthetic Reinforcement.AASHTO R 69-15 is used to determine the long-term allowable material strength, Tal, that is solely product property performance dependant.1.2 This guide is intended to assist designers and users of reinforcement geosynthetics when reviewing reports of reduction factor testing efforts. This guide is not intended to replace education or experience, or other alternative design procedures.This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. Not all aspects of this guide may be applicable in all circumstances. The word “standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

1.1This guide presents a description of how to use test results from reduction factor test reports for reinforcement geosynthetics. It is based solely on testing and reporting requirements as established in American Association of State Highway and Transportation Officials (AASHTO) standard AASHTO R 69-15, Standard Practice for Determination of Long-Term Strength for Geosynthetic Reinforcement. AASHTO R 69-15 is used to determine the long-term allowable material strength, Tal, that is solely product property performance dependant.

1.2This guide is intended to assist designers and users of reinforcement geosynthetics when reviewing reports of reduction factor testing efforts. This guide is not intended to replace education or experience, or other alternative design procedures. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. Not all aspects of this guide may be applicable in all circumstances. The word “standard” in the title of this document means only that the document has been approved through the ASTM consensus process.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 35
DocumentType
Guide
Pages
7
PublisherName
American Society for Testing and Materials
Status
Current

ASTM D 4603 : 2003 Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer
ASTM D 5262 : 2006 Standard Test Method for Evaluating the Unconfined Tension Creep Rupture Behavior of Geosynthetics
ASTM D 5721 : 2008 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM D 6637/D6637M : 2015 : R2023 Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
ASTM D 5721 : 2008 : R2013 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM D 6637/D6637M : 2015 Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
ASTM D 5262 : 2007 : R2016 Standard Test Method for Evaluating the Unconfined Tension Creep and Creep Rupture Behavior of Geosynthetics
ASTM D 5818 : 2011 Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics
ASTM D 5818 : 1995 : R2000 Standard Practice for Obtaining Samples of Geosynthetics from a Test Section for Assessment of Installation Damage
ASTM D 4595 : 1986 : R2001 Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method
ASTM D 5262 : 2004 Standard Test Method for Evaluating the Unconfined Tension Creep Behavior of Geosynthetics
ASTM D 5818 : 2022 Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics
ASTM D 4595 : 2011 Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method
ASTM D 5262 : 2021 Standard Test Method for Determining the Unconfined Tension Creep and Creep Rupture Behavior of Planar Geosynthetics Used for Reinforcement Purposes
ASTM D 5818 : 2006 Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics
ASTM D 4603 : 2018 Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer
ASTM D 5262 : 2002 : REV A Standard Test Method for Evaluating the Unconfined Tension Creep Behavior of Geosynthetics
ASTM D 6992 : 2016 : R2023 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 5721 : 1995 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM D 5262 : 1997 Standard Test Method for Evaluating the Unconfined Tension Creep Behavior of Geosynthetics
ASTM D 4603 : 1996 Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer
ASTM D 6992 : 2003 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 5818 : 2011 : R2018 Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics
ASTM D 5262 :2007 Standard Test Method for Evaluating the Unconfined Tension Creep and Creep Rupture Behavior of Geosynthetics
ASTM D 6992 : 2016 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 4595 : 1986 : R1994 Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method
ASTM D 4355/D4355M : 2021 Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture, and Heat in a Xenon Arc-Type Apparatus
ASTM D 5818 : 2011 : R2022 Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics
ASTM D 5262 : 2007 : R2012 Standard Test Method for Evaluating the Unconfined Tension Creep and Creep Rupture Behavior of Geosynthetics
ASTM D 4595 : 2017 Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method
ASTM D 6992 : 2003 : R2009 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 5721 : 2008 : R2018 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM D 4355/D4355M : 2014 : R2018 Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc-Type Apparatus
ASTM D 6992 : 2003 : R2015 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 7409 : 2007 Standard Test Method for Carboxyl End Group Content of Polyethylene Terephthalate (PET) Yarns
ASTM D 4595 : 2009 Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method
ASTM D 5721 : 2022 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM D 7409 : 2015 Standard Test Method for Carboxyl End Group Content of Polyethylene Terephthalate (PET) Yarns
ASTM D 7409 : 2007 : EDT 1 Standard Test Method for Carboxyl End Group Content of Polyethylene Terephthalate (PET) Yarns
ASTM D 4595 : 2005 Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method
ASTM D 4603 : 2003 : R2011 : EDT 1 Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer

View more information
US$63.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.