Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

05-01-2019

Publisher

American Society for Testing and Materials

This specification describes an alcohol-carboxylic acid blend, referred to as the microemulsion blendstock.

1.1This specification describes an alcohol-carboxylic acid blend, referred to as the microemulsion blendstock.

1.1.1Warning—The microemulsion blendstock should be stored in facilities and equipment designed for oxygenated and low flashpoint liquids.

1.2The microemulsion blendstock is to be blended with fuel oils to produce a microemulsion test fuel oil that consists of inverse micelles.

Note 1:While no fuel standard currently exists for a microemulsion test fuel oil, work to develop one is underway.

Note 2:Typical fuel oils that could be used for blending with microemulsion blendstock are fuels that comply with Specifications D975 and D396 and may contain up to 5 % by volume biodiesel.

Note 3:Testing with test fuels containing 10 % microemulsion blendstock using B5 as a base fuel did not show any detrimental changes to specified fuel properties relative to B0 base fuels, but can impair measurement of microemulsion blendstock concentration.

1.2.1The microemulsion test fuel oil (to be made from this blendstock) is to be used for testing and demonstration purposes only in specific equipment and vehicles that are suited for or have been equipped with safety precautions for use with low flashpoint fuels and oxygenated fuels such as ethanol. Minimum safety precautions may include flame arrestors and grounding straps.

Note 4:The low flash point of this blendstock relative to conventional diesel fuel increases certain hazards during storage and distribution.

1.3Nothing in this specification shall preclude observance of federal, state, or local regulations, which may be more restrictive.

1.4The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 02
DocumentType	Standard
Pages	8
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM D 8181 : 2018 : REV B

ASTM D 4175 : 2020	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2014	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4057 : 2019	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4806 : 2021	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2009 : REV A : EDT 1	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 6584 : 2008	Standard Test Method for Determination of Free and Total Glycerin in B-100 Biodiesel Methyl Esters By Gas Chromatography
ASTM D 4175 : 2008 : REV B : EDT 1	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2002	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 974 : 2014 : EDT 2	Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 4057 : 1995	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 974 : 2001	Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 4175 : 2005	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2016	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2005 : EDT 2	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4625 : 2003	Standard Test Method for Distillate Fuel Storage Stability at 43°C (110°F)
ASTM D 4806 : 2021 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7862 : 2021	Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7042 : 2019 : EDT 1	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4175 : 2015 : REV C	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7862 : 2015 : REV A	Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2020 : REV B	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7862 : 2019	Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2017 : REV A : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 396 : 2020	Standard Specification for Fuel Oils
ASTM D 4806 : 2007 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 664 : 2017 : REV A	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 7042 : 2012	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 975 : 2022	Standard Specification for Diesel Fuel
ASTM D 6751 : 2006 : REV A	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4175 : 2008 : REV A	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2020 : REV A	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4057 : 2012 : R2018	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6584 : 2010 : REV A	Standard Test Method for Determination of Total Monoglyceride, Total Diglyceride, Total Triglyceride, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography
ASTM D 7545 : 2014 : R2019 : EDT 1	Standard Test Method for Oxidation Stability of Middle Distillate Fuels—Rapid Small Scale Oxidation Test (RSSOT)
ASTM D 6751 : 2007 : REV B	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 396 : 1998	Standard Specification for Fuel Oils
ASTM D 6751 : 2006 : EDT 1	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4175 : 2017 : REV B	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2009	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 6751 : 2018	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 6751 : 2009 : REV A	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 3242 : 1998	Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D 6751 : 2007 : REV B : EDT 1	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 7042 : 2016 : EDT 2	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4806 : 2015	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6584 : 2010	Standard Test Method for Determination of Total Monoglyceride, Total Diglyceride, Total Triglyceride, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography
ASTM D 4806 : 2006 : REV B	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 975 : 2019 : REV B	Standard Specification for Diesel Fuel
ASTM D 7545 : 2013	Standard Test Method for Oxidation Stability of Middle Distillate Fuels—Rapid Small Scale Oxidation Test (RSSOT)
ASTM D 4175 : 2022	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6751 : 2007	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 7042 : 2010	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4175 : 2009 : REV A : EDT 4	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2009 : REV A : EDT 3	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 974 : 2022	Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 4806 : 2006 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4057 : 1981 : EDT 2	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6751 : 2012	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 6584 : 2021	Standard Test Method for Determination of Total Monoglycerides, Total Diglycerides, Total Triglycerides, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography
ASTM D 7862 : 2013	Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7042 : 2016 : EDT 1	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 445 : 2021 : EDT 2	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 975 : 2021	Standard Specification for Diesel Fuel
ASTM D 4175 : 2018	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4806 : 2006	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6584 : 2010 : REV A : EDT 1	Standard Test Method for Determination of Total Monoglyceride, Total Diglyceride, Total Triglyceride, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography
ASTM D 975 : 2023 : REV A	Standard Specification for Diesel Fuel
ASTM D 974 : 2021	Standard Test Method for Acid and Base Number by Color-Indicator Titration
ASTM D 4806 : 2001	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 445 : 2017 : REV A	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 6751 : 2014	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4175 : 2001 : EDT 1	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2020 : REV B : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4806 : 2014	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4625 : 2021	Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F)
ASTM D 4175 : 2001	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2005 : EDT 1	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2004 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2022 : REV A	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7862 : 2015	Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2013	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7042 : 2020	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 3242 : 2007	Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D 4175 : 2002	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7545 : 2009	Standard Test Method for Oxidation Stability of Middle Distillate Fuels<span class='unicode'>—</span>Rapid Small Scale Oxidation Test (RSSOT)
ASTM D 4806 : 2001 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 445 : 1988	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity)
ASTM D 6751 : 2011 : REV B	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 975 : 2020 : REV C	Standard Specification for Diesel Fuel
ASTM D 4806 : 2003	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2023	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6751 : 2015 : REV B	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4806 : 2008 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4057 : 2006	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4806 : 2018 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 3242 : 2001	Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D 4175 : 2015	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2002 : REV A : EDT 2	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2017	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4625 : 1992 : R1998	Standard Test Method for Distillate Fuel Storage Stability at 43&#176C (110&#176F)
ASTM D 4806 : 2010 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7042 : 2011 : REV A	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 6751 : 2015 : REV C	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4806 : 2011 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4625 : 2016	Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F)
ASTM D 6751 : 2015 : REV A	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 6584 : 2000	Test Method for Determination of Free and Total Glycerine in B-100 Biodiesel Methyl Esters by Gas Chromatography
ASTM D 4057 : 2012	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 3242 : 2008	Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D 7042 : 2021	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 3242 : 2005	Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D 4175 : 2022 : REV A : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 665 : 2023	Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
ASTM D 664 : 1995	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 4806 : 2016 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6584 : 2013 : EDT 1	Standard Test Method for Determination of Total Monoglycerides, Total Diglycerides, Total Triglycerides, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography
ASTM D 4175 : 2009 : REV A : EDT 5	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2016 : REV C	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2015 : REV B	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 6751 : 2002	Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels
ASTM D 6751 : 2003 : REV A	Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels
ASTM D 4175 : 2015 : REV A	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7042 : 2004	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4806 : 2007	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2019	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2004	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2010	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6584 : 2000 : EDT 1	Standard Test Method for Determination of Free and Total Glycerin in B-100 Biodiesel Methyl Esters By Gas Chromatography
ASTM D 445 : 2019 : REV A	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 6751 : 2023 : REV A	Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels
ASTM D 4175 : 2009 : REV A	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 97 : 2017 : REV B	Standard Test Method for Pour Point of Petroleum Products
ASTM D 4625 : 2004	Standard Test Method for Distillate Fuel Storage Stability at 43°C (110°F)
ASTM D 6751 : 2020	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4806 : 2011	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2016 : REV B	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6751 : 2020 : REV A	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 7042 : 2019	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4806 : 2013 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2002 : REV A : EDT 1	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2008	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2019 : REV A	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6751 : 2003	Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels
ASTM D 6751 : 2008	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 6751 : 2019	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4175 : 2002 : REV A	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2000 : EDT 1	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4175 : 2016 : REV A	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7545 : 2014	Standard Test Method for Oxidation Stability of Middle Distillate Fuels—Rapid Small Scale Oxidation Test (RSSOT)
ASTM D 4625 : 2004 : R2009	Standard Test Method for Distillate Fuel Storage Stability at 43°C (110°F)
ASTM D 4806 : 2018	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7042 : 2012 : REV A	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 445 : 2019	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4175 : 2023 : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2023 : REV A	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2019 : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4625 : 2014	Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F)
ASTM D 4175 : 2022 : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 130 : 2018	Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM D 7042 : 2016 : EDT 3	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4806 : 2008	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6751 : 2015 : REV C : EDT 1	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 975 : 2022 : REV A	Standard Specification for Diesel Fuel
ASTM D 396 : 2021	Standard Specification for Fuel Oils
ASTM D 445 : 2001	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity)
ASTM D 97 : 2017 : REV B : R2022	Standard Test Method for Pour Point of Petroleum Products
ASTM D 664 : 2011 : REV A	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 6751 : 2023	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4806 : 2006 : REV C	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 396 : 2009	Standard Specification for Fuel Oils
ASTM D 6751 : 2007 : REV A	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 445 : 2024	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 445 : 2021	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 6584 : 2017	Standard Test Method for Determination of Total Monoglycerides, Total Diglycerides, Total Triglycerides, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography
ASTM D 4175 : 2017 : REV A	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 7862 : 2018	Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4057 : 2022	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 975 : 2023	Standard Specification for Diesel Fuel
ASTM D 7042 : 2012 : EDT 1	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 6751 : 2011	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4175 : 2009 : REV A : EDT 2	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 4806 : 2009	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 7042 : 2021 : REV A	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4806 : 2020	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4806 : 2012	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2018 : EDT 1	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4175 : 2016	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6751 : 2011 : REV A	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 6751 : 2015	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 445 : 2018	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 3242 : 2023	Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D 665 : 2019	Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
ASTM D 7042 : 2016	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4806 : 2010 : REV B	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 6584 : 2013	Standard Test Method for Determination of Total Monoglycerides, Total Diglycerides, Total Triglycerides, and Free and Total Glycerin in B-100 Biodiesel Methyl Esters by Gas Chromatography
ASTM D 445 : 2021 : EDT 1	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4057 : 1995 : R2000	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4625 : 2016 : EDT 1	Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F)
ASTM D 3242 : 2011 : R2017	Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D 4175 : 2017	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 4806 : 1999	Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
ASTM D 4175 : 2019	Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6751 : 2009	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 4057 : 2006 : R2011	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4175 : 2015 : REV B : EDT 1	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 6584 : 2007	Standard Test Method for Determination of Free and Total Glycerin in B-100 Biodiesel Methyl Esters By Gas Chromatography
ASTM D 6751 : 2010	Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 445 : 2023	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 130 : 2012	Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM D 4175 : 2008 : REV B	Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants
ASTM D 7042 : 2014	Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 6751 : 2002 : REV A	Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels
ASTM D 3242 : 2011	Standard Test Method for Acidity in Aviation Turbine Fuel
ASTM D 7862 : 2017	Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel