• There are no items in your cart

ASTM D 8198 : 2018

Current
Current

The latest, up-to-date edition.

Standard Specification for Hydraulically Applied 100 % Wood Fiber Mulches
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

07-15-2018

1.1This specification covers the physical properties and testing requirements for 100 % wood fiber Hydraulic Erosion Control Products (HECP) mulches.

1.2Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units, which are provided for information only and are not considered standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard. The sieve designations are identified using the “alternative” system in accordance with Practice E11, such as 3-in. and No. 200, instead of the “standard” of 75-mm and 75-µm, respectively.

1.3All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method.

1.3.1The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 18
DocumentType
Standard
Pages
3
PublisherName
American Society for Testing and Materials
Status
Current

ASTM E 11 : 2020 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
ASTM D 2974 : 2020 Standard Test Methods for Determining the Water (Moisture) Content, Ash Content, and Organic Material of Peat and Other Organic Soils
ASTM D 2976 : 2022 : REV A Standard Test Method for pH of Peat Materials
ASTM D 653 : 2007 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 7367 : 2019 : EDT 2 Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic Planting
ASTM D 3740 : 2012 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2023 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 2976 : 2022 Standard Test Method for pH of Peat Materials
ASTM D 3740 : 2019 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2004 : REV A : EDT 1 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 2974 : 2007 : REV A Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils
ASTM D 7560 : 2016 Standard Test Method for Determination of Fiber Length Percentages in Hydraulic Erosion Control Products (HECPs)
ASTM D 3740 : 2008 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6026 : 2013 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 2976 : 1971 : R1998 Standard Test Method for pH of Peat Materials
ASTM D 6026 : 2006 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 1999 : REV C Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 7367 : 2014 Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic Planting
ASTM D 2974 : 2020 : EDT 1 Standard Test Methods for Determining the Water (Moisture) Content, Ash Content, and Organic Material of Peat and Other Organic Soils
ASTM E 11 : 2022 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
ASTM D 653 : 2022 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 7367 : 2019 Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic Planting
ASTM D 653 : 2020 : EDT 1 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 2974 : 2000 Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils
ASTM D 6026 : 1999 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 2974 : 2007 Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils
ASTM D 3740 : 2011 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 7560 : 2016 : EDT 1 Standard Test Method for Determination of Fiber Length Percentages in Hydraulic Erosion Control Products (HECPs)
ASTM D 6026 : 2001 : EDT 1 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2010 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 653 : 2021 : REV A Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 6026 : 1996 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2004 : REV A Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 2974 : 2014 Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils
ASTM D 7367 : 2019 : EDT 1 Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic Planting
ASTM D 3740 : 2001 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 2974 : 2013 Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils
ASTM D 653 : 2021 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2021 : REV B Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 7560 : 2022 Standard Test Method for Determination of Fiber Length Percentages in Hydraulic Erosion Control Products (HECPs)
ASTM D 2976 : 2015 Standard Test Method for pH of Peat Materials
ASTM D 6026 : 1996 : EDT 1 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2012 : REV A Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2003 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 7367 : 2007 Standard Test Method for Determining Water Holding Capacity of Fiber Mulches for Hydraulic Planting
ASTM D 6026 : 2021 Standard Practice for Using Significant Digits and Data Records in Geotechnical Data
ASTM D 6026 : 2001 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 2976 : 1971 : R2004 Standard Test Method for pH of Peat Materials (Withdrawn 2013)
ASTM D 3740 : 2004 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction

View more information
US$55.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.