• There are no items in your cart

ASTM D 8326 : 2021

Current
Current

The latest, up-to-date edition.

Standard Practice for Measurement of the Kinetic Energy of Simulated Rainfall
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-21-2021

1.1This practice is used to measure the kinetic energy of rainfall simulators used by laboratories to evaluate soil erosion. The kinetic energy of raindrops is an important factor that should be considered when conducting soil erosion studies. Using the data collected from determining the raindrop size, this practice provides a method to uniformly calculate the kinetic energy which can be used to compare results from different laboratories.

1.2Many types of Erosion Control Products (ECPs) are evaluated for their ability to reduce soil erosion in laboratory and field settings using rainfall simulators. Rainfall simulators are used with test plots to simulate a specific condition that is or may be expected in the field. Rainfall simulators typically use drop emitters, sprinklers, or nozzles to create the raindrops. Each device produces different drops and since the rainfall simulators can be configured to produce different raindrop sizes and fall heights, the kinetic energy will be different. Therefore, the kinetic energy must be calculated for a given set of conditions in order to properly understand the impact of erosion for bare soil and the ECP.

1.3The upper limit of the size of a raindrop is generally accepted to be 7 mm. While it is possible to get a raindrop size between 6 and 7 mm occasionally, it is not common to get raindrop sizes above 6 mm.

1.4Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.

1.5All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.5.1The procedures used to specify how data are collected/recorded or calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

1.6This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 18
DocumentType
Standard Practice
Pages
6
PublisherName
American Society for Testing and Materials
Status
Current

ASTM D 653 : 2007 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 3740 : 2023 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2019 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6026 : 2013 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 653 : 2022 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2020 : EDT 1 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2021 : REV A Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2021 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2021 : REV B Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 6026 : 1996 : EDT 1 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 6026 : 2021 Standard Practice for Using Significant Digits and Data Records in Geotechnical Data

View more information
US$63.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.