• There are no items in your cart

ASTM E 1030/E1030M : 2021

Current
Current

The latest, up-to-date edition.

Standard Practice for Radiographic Examination of Metallic Castings
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

06-30-2021

1.1This practice2 provides a uniform procedure for radiographic examination of metallic castings using radiographic film as the recording medium.

1.2This standard addresses the achievement of, or protocols for achieving, common or practical levels of radiographic coverage for castings, to detect primarily volumetric discontinuities to sensitivity levels measured by nominated image quality indicators. All departures, including alternate means or methods to increase coverage, or address challenges of detecting non-volumetric planar-type discontinuities, shall be agreed upon between the purchaser and supplier and shall consider Appendix X1 and Appendix X2.

1.3The radiographic techniques stated herein provide adequate assurance for defect detectability; however, it is recognized that, for special applications, specific techniques using more or less stringent requirements may be required than those specified. In these cases, the use of alternate radiographic techniques shall be as agreed upon between purchaser and supplier (also see Section 5).

1.4Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 07
DocumentType
Standard Practice
Pages
12
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM F 629 : 2020 Standard Practice for Radiography of Cast Metallic Surgical Implants
ASTM F 2895 : 2020 Standard Practice for Digital Radiography of Cast Metallic Implants

ASTM E 1316 : 2022 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 272 : 2021 Standard Reference Radiographs for High-Strength Copper-Base and Nickel-Copper Alloy Castings
ASTM E 1079 : 2021 Standard Practice for Calibration of Transmission Densitometers
ASTM E 543 : 2021 Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 1254 : 2013 : R2023 Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
ASTM E 1815 : 2018 Standard Test Method for Classification of Film Systems for Industrial Radiography
ASTM E 1742/E1742M : 2018 Standard Practice for Radiographic Examination
ASTM E 1316 : 2021 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 280 : 2015 : R2019 : EDT 1 Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings
ASTM E 1316 : 2024 Standard Terminology for <?Pub Dtl?>Nondestructive Examinations
ASTM E 505 : 2015 Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
ASTM E 543 : 2015 Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 1316 : 2021 : REV D Standard Terminology for Nondestructive Examinations
ASTM E 802 : 2019 Standard Reference Radiographs for Gray Iron Castings Up to 4<fraction><num>1</num><den>2</den> </fraction> in. (114 mm) in Thickness
ASTM E 505 : 2022 Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
ASTM E 802 : 2021 Standard Reference Radiographs for Gray Iron Castings Up to 4<fraction><num>1</num><den>2</den> </fraction> in. (114 mm) in Thickness
ASTM E 1316 : 2022 Standard Terminology for Nondestructive Examinations
ASTM E 310 : 2015 : R2019 : EDT 1 Standard Reference Radiographs for Tin Bronze Castings
ASTM E 1316 : 2021 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 280 : 2021 Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings
ASTM E 1742/E1742M : 2023 Standard Practice for Radiographic Examination
ASTM E 272 : 2019 Standard Reference Radiographs for High-Strength Copper-Base and Nickel-Copper Alloy Castings
ASTM E 1316 : 2023 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1254 : 2013 : R2018 Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
ASTM E 310 : 2021 Standard Reference Radiographs for Tin Bronze Castings
ASTM E 1316 : 2021 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 1079 : 2016 Standard Practice for Calibration of Transmission Densitometers
ASTM E 1815 : 2018 : R2023 Standard Test Method for Classification of Film Systems for Industrial Radiography
ASTM E 1316 : 2023 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2023 : REV B Standard Terminology for Nondestructive Examinations

View more information
US$69.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.