Name: ASTM E 1820 : 2020 : REV B
Brand: ASTM
Price: 125.00 USD

ASTM E 1820 : 2020 : REV B

Superseded

View Superseded by

Standard Test Method for Measurement of Fracture Toughness

Available format(s)

Hardcopy , PDF

Superseded date

03-24-2022

Language(s)

English

Published date

11-23-2020

Publisher

American Society for Testing and Materials

1.1This test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value. The fracture toughness determined in accordance with this test method is for the opening mode (Mode I) of loading.

Note 1:Until this version, K_Ic could be evaluated using this test method as well as by using Test Method E399. To avoid duplication, the evaluation of K_Ic has been removed from this test method and the user is referred to Test Method E399.

1.2The recommended specimens are single-edge bend, [SE(B)], compact, [C(T)], and disk-shaped compact, [DC(T)]. All specimens contain notches that are sharpened with fatigue cracks.

1.2.1Specimen dimensional (size) requirements vary according to the fracture toughness analysis applied. The guidelines are established through consideration of material toughness, material flow strength, and the individual qualification requirements of the toughness value per values sought.

Note 2:Other standard methods for the determination of fracture toughness using the parameters K, J, and CTOD are contained in Test Methods E399, E1290, and E1921. This test method was developed to provide a common method for determining all applicable toughness parameters from a single test.

1.3The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	E 08
DocumentType	Test Method
Pages	65
PublisherName	American Society for Testing and Materials
Status	Superseded
SupersededBy	ASTM E 1820 : 2021
Supersedes	ASTM E 1820 : 2020 : REV A : EDT 1

NIST GCR 22-917-51:2022	Research Plan for the Study of Pre-Northridge Earthquake PJP-welded Column Splices and Weak Panel Zones
ASTM E 647 : 2015 : EDT 1	Standard Test Method for Measurement of Fatigue Crack Growth Rates
ASTM E 2215 : 2019	Standard Practice for Evaluation of Surveillance Capsules from Light-Water Moderated Nuclear Power Reactor Vessels
ASTM E 2818 : 2011(R2019)	Standard Practice for Determination of Quasistatic Fracture Toughness of Welds
ASTM E 636 : 2020	Standard Guide for Conducting Supplemental Surveillance Tests for Nuclear Power Reactor Vessels
ASTM E 2472 : 2012 : R2018 : EDT 1	Standard Test Method for Determination of Resistance to Stable Crack Extension under Low-Constraint Conditions
ASTM E 1457 : 2019 : EDT 1	Standard Test Method for Measurement of Creep Crack Growth Times in Metals
ASTM E 2899 : 2019 : EDT 1	Standard Test Method for Measurement of Initiation Toughness in Surface Cracks Under Tension and Bending
ASTM A 1099/A1099M : 2020	Standard Specification for Modified Alloy Steel Forgings, Forged Bar, and Rolled Bar Commonly Used in Oil and Gas Pressure Vessels
ASTM E 399 : 2020 : REV A	Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials
ASTM E 509/E509M : 2021	Standard Guide for In-Service Annealing of Light-Water Moderated Nuclear Reactor Vessels
ASTM E 185 : 2021	Standard Practice for Design of Surveillance Programs for Light-Water Moderated Nuclear Power Reactor Vessels
ASTM E 1253 : 2021	Standard Guide for Reconstitution of Charpy-Sized Specimens
ASTM F 3001 : 2014 : R2021	Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium ELI (Extra Low Interstitial) with Powder Bed Fusion
ASTM F 3056 : 2014 : R2021	Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion
ASTM E 1823 : 2021	Standard Terminology Relating to Fatigue and Fracture Testing
ASTM F 3055 : 2014 : REV A : R2021	Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion
ASTM F 2924 : 2014 : R2021	Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion
ASTM E 1921 : 2021 : REV A	Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >0</inf></emph>, for Ferritic Steels in the Transition Range
ASTM F 3122 : 2014	Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes
ASTM F 3184 : 2016	Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion
ASTM F 3213 : 2017	Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Cobalt-28 Chromium-6 Molybdenum via Powder Bed Fusion
ASTM F 3302 : 2018	Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Titanium Alloys via Powder Bed Fusion
ASTM F 3318 : 2018	Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam

ASTM E 8/E8M : 2016 : REV A : EDT 1	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 8/E8M : 2021	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 21 : 2020	Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
ASTM E 399 : 2020 : REV A	Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials
ASTM E 1921 : 2021 : REV A	Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >0</inf></emph>, for Ferritic Steels in the Transition Range
ASTM E 1921 : 2019 : REV B	Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >o</inf></emph>, for Ferritic Steels in the Transition Range
ASTM E 1823 : 2021	Standard Terminology Relating to Fatigue and Fracture Testing
ASTM E 23 : 2002	Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
ASTM E 1921 : 2011	Standard Test Method for Determination of Reference Temperature, <span class="bdit">T<sub>o</sub></span>, for Ferritic Steels in the Transition Range
ASTM E 4 : 2021	Standard Practices for Force Calibration and Verification of Testing Machines
ASTM E 1921 : 2021	Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >o</inf></emph>, for Ferritic Steels in the Transition Range
ASTM E 1921 : 2020	Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >o</inf></emph>, for Ferritic Steels in the Transition Range
ASTM E 1823 : 2020 : REV B	Standard Terminology Relating to Fatigue and Fracture Testing