• There are no items in your cart

ASTM E 2243 : 2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Re-contouring and Highwall Reclamation
Available format(s)

Hardcopy , PDF

Superseded date

09-17-2019

Language(s)

English

Published date

10-01-2013

CONTAINED IN VOL. 11.05, 2014 Specifies the use of coal combustion products (CCPs) for surface coal mine reclamation applications, as in beneficial use for reestablishing land contours, highwall reclamation, and other reclamation activities requiring fills or soil replacement.

1.1This guide covers the use of coal combustion products (CCPs) for surface coal mine reclamation applications, as in beneficial use for reestablishing land contours, highwall reclamation, and other reclamation activities requiring fills or soil replacement. The purpose of this standard is to provide guidance on identification of CCPs with appropriate engineering and environmental performance appropriate for surface mine re-contouring and highwall reclamation applications. It does not apply to underground mine reclamation applications. There are many important differences in physical and chemical characteristics among the various types of CCPs available for use in mine reclamation. CCPs proposed for each project must be investigated thoroughly to design CCP placement activities to meet the project objectives. This guide provides procedures for consideration of engineering, economic, and environmental factors in the development of such applications, and should be used in conjunction with professional judgement. This guide is not intended to replace the standard of care by which the adequacy of a given professional service must be judged, nor should this guide be applied without consideration of a project's unique aspects.

1.2The utilization of CCPs under this guide is a component of a pollution prevention program; Guide E1609 describes pollution prevention activities in more detail. Utilization of CCPs in this manner conserves land, natural resources, and energy.

1.3This guide applies to CCPs produced primarily from the combustion of coal.

1.4The testing, engineering, and construction practices for using CCPs in mine reclamation are similar to generally accepted practices for using other materials, including cement and soils, in mine reclamation. For guidance on structural fills to be constructed at mine sites, see applicable ASTM guide for coal ash structural fills.

1.5Regulations governing the use of CCPs vary by state. The user of this standard guide has the responsibility to determine and comply with applicable regulations.

1.6The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 50
DocumentType
Guide
Pages
12
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 2216 : 2005 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 75 : 2003 Standard Practice for Sampling Aggregates
ASTM D 4253 : 2014 Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
ASTM D 422 : 1963 : R2002 : EDT 1 Standard Test Method for Particle-Size Analysis of Soils
ASTM D 4253 : 2016 Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
ASTM D 4767 : 2011 Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils
ASTM D 3550 : 1984 : R1995 : EDT 1 Standard Practice for Thick Wall, Ring-Lined, Split Barrel, Drive Sampling of Soils
ASTM D 1452 : 2009 Standard Practice for Soil Exploration and Sampling by Auger Borings
ASTM D 1586 : 2008 : REV A Standard Test Method for Standard Penetration Test (SPT) and Split-Barrel Sampling of Soils
ASTM D 4448 : 2001 : R2019 Standard Guide for Sampling Ground-Water Monitoring Wells
ASTM D 1557 : 2007 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>))
ASTM D 1196 : 1993 : R1997 Standard Test Method for Nonrepetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport and Highway Pavements
ASTM D 4972 : 1995 : REV A Standard Test Method for pH of Soils
ASTM D 2216 : 2010 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 5084 : 2016 : REV A Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter
AASHTO T 288 : 2012 METHOD OF TEST FOR DETERMINING MINIMUM LABORATORY SOIL RESISTIVITY
ASTM D 1586 : 1999 Standard Test Method for Penetration Test and Split-Barrel Sampling of Soils
ASTM D 1586 : 2008 Standard Test Method for Standard Penetration Test (SPT) and Split-Barrel Sampling of Soils
ASTM D 1883 : 1999 Standard Test Method for CBR (California Bearing Ratio) of Laboratory-Compacted Soils
ASTM D 4254 : 2000 : R2006 : EDT 1 Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
ASTM D 1883 : 2007 : EDT 1 Standard Test Method for CBR (California Bearing Ratio) of Laboratory-Compacted Soils
ASTM D 4448 : 1985 : REV A : R1992 Standard Guide for Sampling Ground-Water Monitoring Wells
ASTM D 4448 : 2001 : R2013 Standard Guide for Sampling Ground-Water Monitoring Wells
ASTM D 5084 : 2003 Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter
ASTM D 5851 : 1995 : R2006 Standard Guide for Planning and Implementing a Water Monitoring Program
ASTM D 1883 : 2007 Standard Test Method for CBR (California Bearing Ratio) of Laboratory-Compacted Soils
ASTM D 4254 : 2016 Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
ASTM D 1883 : 2016 Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils
ASTM D 1452 : 2007 : REV A Standard Practice for Soil Investigation and Sampling by Auger Borings
ASTM D 2435 : 2002 Standard Test Method for One-Dimensional Consolidation Properties of Soils
ASTM D 2166 : 2000 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
ASTM D 4448 : 2001 : R2007 Standard Guide for Sampling Ground-Water Monitoring Wells
ASTM D 1196 : 1993 : R2004 Standard Test Method for Nonrepetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport and Highway Pavements
ASTM D 1195 : 1993 : R2004 Standard Test Method for Repetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport and Highway Pavements
ASTM D 4253 : 2000 Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
ASTM D 4767 : 1995 Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils
ASTM D 5239 : 1998 Standard Practice for Characterizing Fly Ash for Use in Soil Stabilization
ASTM D 1883 : 2016 : REDLINE Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils
ASTM D 5239 : 2012 : EDT 1 Standard Practice for Characterizing Fly Ash for Use in Soil Stabilization (Withdrawn 2021)
ASTM D 1586 : 2011 Standard Test Method for Standard Penetration Test (SPT) and Split-Barrel Sampling of Soils
ASTM D 3080 : 2004 Standard Test Method for Direct Shear Test of Soils Under Consolidated Drained Conditions
ASTM D 854 : 2014 : REDLINE Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer (Withdrawn 2023)
ASTM D 4254 : 2014 Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
ASTM D 2166 : 2006 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
ASTM D 5239 : 2012 Standard Practice for Characterizing Fly Ash for Use in Soil Stabilization
ASTM D 4253 : 2000 : R2006 Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
ASTM D 4972 : 2013 Standard Test Method for pH of Soils
ASTM D 698 : 2013-05 TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3]))
ASTM D 5851 : 1995 : R2000 Standard Guide for Planning and Implementing a Water Monitoring Program
ASTM D 3877 : 2008 Standard Test Methods for One-Dimensional Expansion, Shrinkage, and Uplift Pressure of Soil-Lime Mixtures (Withdrawn 2017)
ASTM D 2435 : 1996 Standard Test Method for One-Dimensional Consolidation Properties of Soils
ASTM D 1883 : 2005 Standard Test Method for CBR (California Bearing Ratio) of Laboratory-Compacted Soils
ASTM D 420 : 1998 Guide to Site Characterization for Engineering, Design, and Construction Purposes
ASTM D 2166 : 2000 : EDT 1 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
ASTM D 1557 : 2012 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>))
ASTM D 1557 : 2012 : EDT 1 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>))
ASTM D 5084 : 2016 Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter
ASTM D 4429 : 1993 Standard Test Method for CBR (California Bearing Ratio) of Soils in Place (Withdrawn 2002)
ASTM D 1195 : 1993 : R1997 Standard Test Method for Repetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport and Highway Pavements
ASTM D 4254 : 2000 Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
ASTM D 4254 : 2016 : REDLINE Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
ASTM D 1883 : 2014 Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils
AASHTO T 289 : 1991 METHOD OF TEST FOR DETERMINING PH OF SOIL FOR USE IN CORROSION TESTING
ASTM D 4972 : 2001 : R2007 Standard Test Method for pH of Soils
ASTM D 5084 : 2010 Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter
ASTM D 5851 : 1995 : R2011 Standard Guide for Planning and Implementing a Water Monitoring Program
ASTM D 2216 : 2019 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 3877 : 2002 Standard Test Methods for One-Dimensional Expansion, Shrinkage, and Uplift Pressure of Soil-Lime Mixtures
ASTM D 4767 : 2004 Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils
ASTM D 3550 : 2001 : R2007 Standard Practice for Thick Wall, Ring-Lined, Split Barrel, Drive Sampling of Soils (Withdrawn 2016)
ASTM D 1557 : 2002 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup>(2,700 kN-m/m<sup>3</sup>))
ASTM D 3877 : 1996 Standard Test Methods for One-Dimensional Expansion, Shrinkage, and Uplift Pressure of Soil-Lime Mixtures
ASTM D 4429 : 2004 Standard Test Method for CBR (California Bearing Ratio) of Soils in Place
ASTM D 1557 : 2000 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup>(2,700 kN-m/m<sup>3</sup>))
ASTM D 5851 : 1995 : R2015 Standard Guide for Planning and Implementing a Water Monitoring Program
ASTM D 3080 : 1998 Standard Test Method for Direct Shear Test of Soils Under Consolidated Drained Conditions
ASTM D 1452 : 2007 Standard Practice for Soil Investigation and Sampling by Auger Borings
ASTM E 1609 : 2001 Standard Guide for Development and Implementation of a Pollution Prevention Program (Withdrawn 2010)
ASTM E 2201 : 2002 : REV A Standard Terminology for Coal Combustion Products (Withdrawn 2011)
ASTM D 2435 : 2004 Standard Test Methods for One-Dimensional Consolidation Properties of Soils Using Incremental Loading
AASHTO T 290 : 1995 METHOD OF TEST FOR DETERMINING WATER-SOLUBLE SULFATE ION CONTENT IN SOIL
ASTM D 5239 : 2004 Standard Practice for Characterizing Fly Ash for Use in Soil Stabilization
ASTM D 5084 : 2000 Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter
ASTM D 2216 : 1998 Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 4448 : 2001 Standard Guide for Sampling Ground-Water Monitoring Wells
ASTM E 2201 : 2002 Standard Terminology for Coal Combustion Products
ASTM D 4972 : 2019 Standard Test Methods for pH of Soils
ASTM D 4767 : 2002 Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils
ASTM D 2216 : 1971 Standard Method of Laboratory Determination Of Moisture Content Of Soil
ASTM D 4429 : 2009 : REV A Standard Test Method for CBR (California Bearing Ratio) of Soils in Place (Withdrawn 2018)
ASTM D 4972 : 2001 Standard Test Method for pH of Soils
ASTM D 4253 : 2016 : REDLINE Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
AASHTO T 291 : 1994 METHOD OF TEST FOR DETERMINING WATER-SOLUBLE CHLORIDE ION CONTENT IN SOIL
ASTM D 1557 : 2009 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>))
ASTM D 4972 : 2018 Standard Test Methods for pH of Soils
ASTM D 4254 : 2000 : R2006 Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
ASTM E 1609 : 1994 Standard Guide for Development and Implementation of a Pollution Prevention Program
ASTM D 5084 : 2000 : EDT 1 Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter
ASTM D 4767 : 2011 : REDLINE Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils
ASTM D 1883 : 2007 : EDT 2 Standard Test Method for CBR (California Bearing Ratio) of Laboratory-Compacted Soils
ASTM D 4429 : 2009 Standard Test Method for CBR (California Bearing Ratio) of Soils in Place
ASTM D 2435 : 2003 Standard Test Method for One-Dimensional Consolidation Properties of Soils
ASTM D 653 : 2014 : REDLINE Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM E 2201 : 2013 Standard Terminology for Coal Combustion Products
ASTM D 3550 : 2001 Standard Practice for Thick Wall, Ring-Lined, Split Barrel, Drive Sampling of Soils
ASTM D 3080 : 2003 Standard Test Method for Direct Shear Test of Soils Under Consolidated Drained Conditions
ASTM D 1452 : 1980 : R2000 Standard Practice for Soil Investigation and Sampling by Auger Borings

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.