• There are no items in your cart

ASTM E 2251 : 2014 : R2021

Current
Current

The latest, up-to-date edition.

Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

12-08-2021

1.1The purpose of this standard is to specify liquid-in-glass ASTM thermometers using low hazard thermometric liquids defined in this standard.

1.2This standard specifies liquid-in-glass thermometers graduated in degrees Celsius or degrees Fahrenheit that are frequently identified and used in methods under the jurisdiction of the various technical committees within ASTM. The current approved thermometers are listed in Table 1.

1.3The technical requirements for the thermometric liquids used in the thermometers in Table 1 are specified in Annex A1. Tests for conformity to the technical requirements are also found in Annex A1.

Note 1:It has been found by experience that ASTM Thermometers, although developed in general for specific tests, may also be found suitable for other applications, thus precluding the need for new thermometer specifications differing in only minor features. However, it is suggested that technical committees contact E20.05 before choosing a currently designated thermometer for a new method to be sure the thermometer will be suitable for the intended application.

1.4For full rationale, see Appendix X1.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 20
DocumentType
Standard
Pages
18
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM D 6572 : 2021 Standard Test Methods for Determining Dispersive Characteristics of Clayey Soils by the Crumb Test
ASTM D 1755 : 2021 Standard Specification for Poly(Vinyl Chloride) Resins
ASTM D 2251 : 2010 : R2020 Standard Test Method for Metal Corrosion by Halogenated Organic Solvents and Their Admixtures
ASTM D 3603 : 2020 Standard Test Method for Rust-Preventing Characteristics of Steam Turbine Oil in the Presence of Water (Horizontal Disk Method)
ASTM D 4539 : 2017 Standard Test Method for Filterability of Diesel Fuels by Low-Temperature Flow Test (LTFT)
ASTM E 100 : 2019 Standard Specification for ASTM Hydrometers
ASTM D 8175 : 2018 Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Pensky-Martens Closed Cup Tester
ASTM D 2111 : 2010 : R2020 Standard Test Methods for Specific Gravity and Density of Halogenated Organic Solvents and Their Admixtures
ASTM D 2746/D2746M : 2018 Standard Test Method for Staining Tendency of Asphalt (Stain Index)
ASTM D 1480 : 2021 Standard Test Method for Density and Relative Density (Specific Gravity) of Viscous Materials by Bingham Pycnometer
ASTM D 6331 : 2016 Standard Test Method for Determination of Mass Concentration of Particulate Matter from Stationary Sources at Low Concentrations (Manual Gravimetric Method)
ASTM D 6288 : 2017 Standard Practice for Separation and Washing of Recycled Plastics Prior to Testing
ASTM D 5346 : 2017 Standard Test Method for Determination of the Pour Point of Petroleum Oil Used in Fatliquors and Softening Compounds
ASTM E 644 : 2011(R2019) Standard Test Methods for Testing Industrial Resistance Thermometers
ASTM F 483 : 2009 : R2020 Standard Practice for Total Immersion Corrosion Test for Aircraft Maintenance Chemicals
ASTM D 4350 : 2016 Standard Test Method for Corrosivity Index of Plastics and Fillers
ASTM D 5404/D5404M : 2021 Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator
ASTM D 1092 : 2020 Standard Test Method for Measuring Apparent Viscosity of Lubricating Greases
ASTM D 2158 : 2021 Standard Test Method for Residues in Liquefied Petroleum (LP) Gases
ASTM G 42 : 2011 : R2019 : EDT 1 Standard Test Method for Cathodic Disbonding of Pipeline Coatings Subjected to Elevated Temperatures
ASTM D 2838 : 2018 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 5869/D5869M : 2007 : REV A : R2018 : EDT 1 Standard Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials
ASTM D 6926 : 2020 Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus
ASTM F 1914 : 2018 Standard Test Methods for Short-Term Indentation and Residual Indentation of Resilient Floor Covering
ASTM D 8055 : 2017 Standard Guide for Selecting an Appropriate Electronic Thermometer for Replacing Mercury Thermometers in D04 Road and Paving Standards
ASTM C 403/C403M : 2016 Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance
ASTM D 4603 : 2018 Standard Test Method for Determining Inherent Viscosity of Poly(Ethylene Terephthalate) (PET) by Glass Capillary Viscometer
ASTM D 4130 : 2015 Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines (Withdrawn 2024)
ASTM D 6927 : 2015 Standard Test Method for Marshall Stability and Flow of Asphalt Mixtures
ASTM D 1429 : 2013 Standard Test Methods for Specific Gravity of Water and Brine (Withdrawn 2022)
ASTM D 914 : 2012 : R2019 Standard Test Methods for Ethylcellulose
ASTM D 792 : 2020 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D 323 : 2020 : REV A Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method)
ASTM D 4532 : 2015 Standard Test Method for Respirable Dust in Workplace Atmospheres Using Cyclone Samplers
ASTM D 6209 : 2013 Standard Test Method for Determination of Gaseous and Particulate Polycyclic Aromatic Hydrocarbons in Ambient Air (Collection on Sorbent-Backed Filters with Gas Chromatographic/Mass Spectrometric Analysis)
ASTM D 4943 : 2018 Standard Test Method for Shrinkage Factors of Cohesive Soils by the Water Submersion Method
ASTM F 558 : 2021 Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaners
ASTM D 61 : 2015 : R2019 Standard Test Method for Softening Point of Pitches (Cube-in-Water Method)
ASTM D 3154 : 2014 Standard Test Method for Average Velocity in a Duct (Pitot Tube Method)
ASTM D 5478 : 2013 : R2018 Standard Test Methods for Viscosity of Materials by a Falling Needle Viscometer
ASTM D 6539 : 2013 Standard Test Method for Measurement of the Permeability of Unsaturated Porous Materials by Flowing Air (Withdrawn 2022)
ASTM D 3685/D3685M : 2013 : R2021 Standard Test Methods for Sampling and Determination of Particulate Matter in Stack Gases
ASTM D 4889 : 2021 Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Crude or Modified Isocyanates
ASTM C 359 : 2020 Standard Test Method for Early Stiffening of Hydraulic-Cement (Mortar Method)
ASTM D 6784 : 2016 Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method)
ASTM D 1525 : 2017 : EDT 1 Standard Test Method for Vicat Softening Temperature of Plastics
ASTM D 6371 : 2017 : REV A Standard Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels
ASTM D 5438 : 2017 Standard Practice for Collection of Floor Dust for Chemical Analysis
ASTM D 2726/D2726M : 2021 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures
ASTM D 1795 : 2013 : R2021 Standard Test Method for Intrinsic Viscosity of Cellulose
ASTM E 337 : 2015 Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM D 4171 : 2021 Standard Specification for Fuel System Icing Inhibitors
ASTM D 4659 : 2019 Standard Test Methods for Polyurethane Raw Materials: Determination of Specific Gravity of Isocyanates
ASTM D 6084/D6084M : 2021 Standard Test Method for Elastic Recovery of Asphalt Materials by Ductilometer
ASTM D 1608 : 2016 Standard Test Method for Oxides of Nitrogen in Gaseous Combustion Products (Phenol-Disulfonic Acid Procedures) (Withdrawn 2023)
ASTM D 113 : 2017 Standard Test Method for Ductility of Asphalt Materials
ASTM C 1810/C1810M : 2021 : REV A Standard Guide for Comparing Performance of Concrete-Making Materials Using Mortar Mixtures
ASTM D 1321 : 2016 : REV A Standard Test Method for Needle Penetration of Petroleum Waxes
ASTM D 5006 : 2011 : R2021 Standard Test Method for Measurement of Fuel System Icing Inhibitors (Ether Type) in Aviation Fuels
ASTM D 5853 : 2017 : REV A Standard Test Method for Pour Point of Crude Oils
ASTM D 3591 : 2017 Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds
ASTM D 4669 : 2018 Standard Test Method for Polyurethane Raw Materials: Determination of Specific Gravity of Polyols
ASTM D 1125 : 2014 Standard Test Methods for Electrical Conductivity and Resistivity of Water (Withdrawn 2023)
ASTM D 1243 : 2015 Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers
ASTM D 3934 : 2020 Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus
ASTM D 1601 : 2018 Standard Test Method for Dilute Solution Viscosity of Ethylene Polymers
ASTM D 5298 : 2016 Standard Test Method for Measurement of Soil Potential (Suction) Using Filter Paper
ASTM D 2913 : 2020 Standard Test Method for Mercaptan Content of the Atmosphere
ASTM F 2105 : 2021 Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaner Motor/Fan Systems
ASTM D 1310 : 2014 : R2021 Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
ASTM D 5801 : 2017 Standard Test Method for Toughness and Tenacity of Asphalt Materials
ASTM D 972 : 2016 Standard Test Method for Evaporation Loss of Lubricating Greases and Oils
ASTM D 3195/D3195M : 2010 : R2015 Standard Practice for Rotameter Calibration
ASTM D 3642 : 2013 : R2021 Standard Test Method for Softening Point of Certain Alkali-Soluble Resins
ASTM D 4957 : 2018 Standard Test Method for Apparent Viscosity of Asphalt Emulsion Residues and Non-Newtonian Asphalts by Vacuum Capillary Viscometer
ASTM D 7577 : 2012 : R2021 Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends
ASTM E 77 : 2014 : R2021 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 3082 : 2015 Standard Test Method for Boron in Water
ASTM D 3941 : 2020 Standard Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus
ASTM D 3012 : 2019 Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven
ASTM D 8164 : 2021 Standard Guide for Digital Contact Thermometers for Petroleum Products, Liquid Fuels, and Lubricant Testing
ASTM D 5015 : 2015 Standard Test Method for pH of Atmospheric Wet Deposition Samples by Electrometric Determination
ASTM E 126 : 2019 Standard Test Method for Inspection, Calibration, and Verification of ASTM Hydrometers
ASTM E 1 : 2014 : R2020 Standard Specification for ASTM Liquid-in-Glass Thermometers
ASTM D 2732 : 2014 : R2020 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM F 820 : 2021 Standard Test Method for Measuring Air Performance Characteristics of Central Vacuum Cleaning Systems
ASTM D 1074 : 2017 Standard Test Method for Compressive Strength of Asphalt Mixtures
ASTM C 782 : 2013 : R2018 Standard Test Method for Softness of Preformed Tape Sealants
ASTM D 2914 : 2015 Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method)
ASTM D 6925 : 2015 Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor
ASTM D 4878 : 2015 Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Polyols
ASTM D 721 : 2017 Standard Test Method for Oil Content of Petroleum Waxes
ASTM D 5440 : 2017 Standard Test Method for Determining the Melting Point of Fats and Oils
ASTM D 2500 : 2017 : REV A Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 1045 : 2019 Standard Test Methods for Sampling and Testing Plasticizers Used in Plastics

ASTM E 344 : 2020 Terminology Relating to Thermometry and Hydrometry
ASTM E 344 : 2023 Terminology Relating to Thermometry and Hydrometry
ASTM E 563 : 2022 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
ASTM E 563 : 2011 : R2016 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature

View more information
US$69.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.