ASTM E 275 : 2008
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Describing and Measuring Performance of Ultraviolet and Visible Spectrophotometers
Available format(s)
Hardcopy , PDF
Superseded date
09-17-2020
Language(s)
English
Published date
10-15-2008
CONTAINED IN VOL. 03.06, 2015 Defines the description of requirements of spectrophotometric performance, especially for test methods, and the testing of the adequacy of available equipment for a specific method (for example, qualification for a given application).
1.1 This practice covers the description of requirements of spectrophotometric performance, especially for test methods, and the testing of the adequacy of available equipment for a specific method (for example, qualification for a given application). The tests give a measurement of some of the important parameters controlling results obtained in spectrophotometric methods, but it is specifically not to be concluded that all the factors in instrument performance are measured, or in fact may be required for a given application.
1.1.1 This practice is primarily directed to dispersive spectrophotometers used for transmittance measurements rather than instruments designed for diffuse transmission and diffuse reflection.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
E 13
|
| DocumentType |
Standard Practice
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ISO/ASTM 51650:2013 | Practice for use of a cellulose triacetate dosimetry system |
| ISO 15559:1998 | Practice for use of a radiochromic optical waveguide dosimetry system |
| ASTM D 5412 : 1993 : R2011 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
| ASTM E 685 : 1993 : R2013 | Standard Practice for Testing Fixed-Wavelength Photometric Detectors Used in Liquid Chromatography |
| BS ISO 15558:1998 | Practice for use of a polymethylmethacrylate dosimetry system |
| ISO/ASTM 51276:2012 | Practice for use of a polymethylmethacrylate dosimetry system |
| BS ISO 15563:1998 | Practice for use of the ethanol-chlorobenzene dosimetry system |
| ASTM E 169 : 2016 : REDLINE | Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis |
| ASTM E 60 : 2011 | Standard Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry |
| TT-P-2760 Revision A:1994 | PRIMER COATING; POLYURETHANE, ELASTOMERIC |
| BS ISO 15559:1998 | Practice for use of a radiochromic optical waveguide dosimetry system |
| ASTM E 2313 : 2015 : REDLINE | Standard Test Method for Aldehydes in Mono-, Di-, and Triethylene Glycol (using Spectrophotometry) |
| ASTM D 2124 : 1999 : R2011 | Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique (Withdrawn 2020) |
| ASTM D 6697 : 2001 | Standard Test Method for Determination for Chemical Oxygen Demand (Manganese III Oxygen Demand) of Water (Withdrawn 2010) |
| ASTM E 1205 : 2009 | PRACTICE FOR USE OF A CERIC-CEROUS SULFATE DOSIMETRY SYSTEM |
| ASTM D 5412 : 1993 : R2011 : EDT 1 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
| ASTM D 2972 : 2015 : REDLINE | Standard Test Methods for Arsenic in Water |
| ASTM D 6258 : 2017 : REDLINE | Standard Test Method for Determination of Solvent Red 164 Dye Concentration in Diesel Fuels |
| ASTM D 6748 : 2002 | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) |
| ASTM E 925 : 2009 | Standard Practice for Monitoring the Calibration of Ultraviolet-Visible Spectrophotometers whose Spectral Slit Width does not Exceed 2 nm |
| ASTM D 3113 : 1992 : R1998 | Standard Test Methods for Sodium Salts of EDTA in Water (Withdrawn 2005) |
| ASTM D 1840 : 2007 : R2013 | Standard Test Method for Naphthalene Hydrocarbons in Aviation Turbine Fuels by Ultraviolet Spectrophotometry |
| ASTM D 6342 : 2012 : R2017 : EDT 1 | Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy |
| ASTM D 5831 : 2017 : REDLINE | Standard Practice for Screening Fuels in Soils |
| ASTM D 6748 : 2002 : REV A : R2012 | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) |
| ASTM D 3923 : 2008 | Standard Practices for Detecting Leaks in Reverse Osmosis and Nanofiltration Devices |
| ASTM E 1164 : 2012 : EDT 1 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 1310 : 2004 | PRACTICE FOR USE OF A RADIOCHROMIC OPTICAL WAVEGUIDE DOSIMETRY SYSTEM |
| ASTM D 3594 : 1993 : R2000 | Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers |
| ASTM D 4130 : 2015 : REDLINE | Standard Test Method for Sulfate Ion in Brackish Water, Seawater, and Brines |
| ASTM D 1942 : 1980 | Method of Test for Morpholine in Water |
| ISO 15554:1998 | Practice for dosimetry in gamma irradiation facilities for food processing |
| ASTM E 1164 : 2012 : R2017 : EDT 1 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 1276 : 2012 | PRACTICE FOR USE OF A POLYMETHYLMETHACRYLATE DOSIMETRY SYSTEM |
| ASTM D 5412 : 1993 : R2005 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
| ASTM D 1768 : 1989 : R2009 | Standard Test Method for Sodium Alkylbenzene Sulfonate in Synthetic Detergents by Ultraviolet Absorption |
| ASTM D 6122 : 2016-02 | PRACTICE FOR VALIDATION OF THE PERFORMANCE OF MULTIVARIATE ONLINE, AT-LINE, AND LABORATORY INFRARED SPECTROPHOTOMETER BASED ANALYZER SYSTEMS |
| ASTM E 1866 : 1997 : R2013 | Standard Guide for Establishing Spectrophotometer Performance Tests |
| ASTM F 1630 : 2000 | Standard Test Method for Low Temperature FT-IR Analysis of Single Crystal Silicon for III-V Impurities (Withdrawn 2003) |
| ASTM E 1164 : 2012 | Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation |
| ASTM E 424 : 1971 : R2015 | Standard Test Methods for Solar Energy Transmittance and Reflectance (Terrestrial) of Sheet Materials |
| ASTM E 387 : 2004 : R2014 | Standard Test Method for Estimating Stray Radiant Power Ratio of Dispersive Spectrophotometers by the Opaque Filter Method |
| MIL-DTL-7788 Revision H:2011 | PANELS, INFORMATION, INTEGRALLY ILLUMINATED |
| ASTM E 1026 : 2015 : REDLINE | Standard Practice for Using the Fricke Dosimetry System |
| ASTM D 3594 : 1993 | Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers |
| ASTM D 2621 : 1987 : R2011 | Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints |
| BS ISO 15570:1998 | Practice for use of cellulose acetate dosimetry system |
| BS ISO 15557:1998 | Practice for use of a radiochromic film dosimetry system |
| ASTM D 3133 : 2001 | Standard Test Method for Quantitative Determination of Cellulose Nitrate in Alkyd Modified Lacquers by Infrared Spectrophotometry |
| 17/30356677 DC : 0 | BS ISO/ASTM 51538 - PRACTICE FOR USE OF THE ETHANOL-CHLOROBENZENE DOSIMETRY SYSTEM |
| ASTM D 4165 : 2006 | Standard Test Method for Cyanogen Chloride in Water |
| ASTM D 6501 : 2015 : REDLINE | Standard Test Method for Phosphonate in Brines |
| ASTM D 2702 : 2005 : R2016 | Standard Practice for Rubber Chemicals—Determination of Infrared Absorption Characteristics |
| ASTM D 3591 : 2017 : REDLINE | Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds |
| 11/30235530 DC : 0 | BS ISO D 51276 - PRACTICE FOR USE OF A POLYMETHYLMETHACRYLATE DOSIMETRY SYSTEM |
| ASTM D 5086 : 2001 | Standard Test Method for Determination of Calcium, Magnesium, Potassium, and Sodium in Atmospheric Wet Deposition by Flame Atomic Absorption Spectrophotometry |
| 16/30344343 DC : 0 | BS ISO/ASTM 51205 - PRACTICE FOR USE OF A CERIC-CEROUS SULFATE DOSIMETRY SYSTEM |
| ASTM E 512 : 1994 : R2010 | Standard Practice for Combined, Simulated Space Environment Testing of Thermal Control Materials with Electromagnetic and Particulate Radiation |
| ASTM D 6187 : 1997 : R2010 | Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Laser-Induced Fluorescence (Withdrawn 2019) |
| TT-P-2756 Revision A:1996 | POLYURETHANE COATING - SELF-PRIMING TOPCOAT, LOW VOLATILE ORGANIC COMPOUND (VOC) CONTENT |
| MIL-PRF-23942 Revision A:1997 | POLYBUTADIENE, LINEAR, CARBOXYL TERMINATED |
| ASTM D 3650 : 1993 : R2011 | Standard Test Method for Comparison of Waterborne Petroleum Oils By Fluorescence Analysis (Withdrawn 2018) |
| ASTM D 6748 : 2002 : REV A | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) |
| ASTM D 3168 : 1985 : R2005 | Standard Practice for Qualitative Identification of Polymers in Emulsion Paints |
| ISO 15563:1998 | Practice for use of the ethanol-chlorobenzene dosimetry system |
| ASTM D 6748 : 2002 : REV A : R2007 | Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer) <a href="#fn00002"></a> |
| ISO 15570:1998 | Practice for use of cellulose acetate dosimetry system |
| ASTM E 2056 : 2004 : R2010 | Standard Practice for Qualifying Spectrometers and Spectrophotometers for Use in Multivariate Analyses, Calibrated Using Surrogate Mixtures |
| ASTM D 1768 : 1989 : R2016 | Standard Test Method for Sodium Alkylbenzene Sulfonate in Synthetic Detergents by Ultraviolet Absorption |
| ASTM E 387 : 2004 : R2009 | Standard Test Method for Estimating Stray Radiant Power Ratio of Dispersive Spectrophotometers by the Opaque Filter Method |
| ASTM D 4193 : 2008 : R2013 : EDT 1 | Standard Test Method for Thiocyanate in Water |
| ASHRAE 74 : 1998 | METHOD OF MEASURING SOLAR-OPTICAL PROPERTIES OF MATERIALS |
| ASTM E 1866 : 1997 : R2007 | Standard Guide for Establishing Spectrophotometer Performance Tests |
| ASTM D 6303 : 1998 | Standard Test Method for Formaldehyde in Water (Withdrawn 2007) |
| ASTM E 424 : 1971 : R1993 : EDT 1 | Standard Test Methods for Solar Energy Transmittance and Reflectance (Terrestrial) of Sheet Materials |
| ASTM E 1608 : 2015 | Standard Practice for Dosimetry in an X-Ray (Bremsstrahlung) Facility for Radiation Processing at Energies between 50 keV and 7.5 MeV |
| ASTM D 4165 : 2006 : R2012 | Standard Test Method for Cyanogen Chloride in Water |
| ASTM E 1341 : 2016 : REDLINE | Standard Practice for Obtaining Spectroradiometric Data from Radiant Sources for Colorimetry |
| ASTM D 6187 : 1997 : R2003 | Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Laser-Induced Fluorescence |
| ASTM D 3594 : 1993 : R2006 | Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers |
| ASTM D 3168 : 1985 : R2011 | Standard Practice for Qualitative Identification of Polymers in Emulsion Paints |
| ASTM E 685 : 1993 : R2005 | Standard Practice for Testing Fixed-Wavelength Photometric Detectors Used in Liquid Chromatography |
| ASTM D 2124 : 1999 : R2004 | Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique |
| ASTM D 2124 : 1999 : EDT 1 | Standard Test Method for Analysis of Components in Poly(Vinyl Chloride) Compounds Using an Infrared Spectrophotometric Technique |
| ASTM D 3923 : 2008 : R2014 | Standard Practices for Detecting Leaks in Reverse Osmosis and Nanofiltration Devices |
| ASTM E 1538 : 2009 | PRACTICE FOR USE OF THE ETHANOL-CHLOROBENZENE DOSIMETRY SYSTEM |
| ASTM E 1866 : 1997 | Standard Guide for Establishing Spectrophotometer Performance Tests |
| ASTM G 178 : 2016 : REDLINE | Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique |
| ASTM D 5412 : 1993 : R2000 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
| ASTM E 685 : 1993 : R2000 | Standard Practice for Testing Fixed-Wavelength Photometric Detectors Used in Liquid Chromatography |
| ASTM D 4763 :2006 | Standard Practice for Identification of Chemicals in Water by Fluorescence Spectroscopy |
| ASTM D 2621 : 1987 : R2016 | Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints |
| ASTM E 925 : 2009 : R2014 | Standard Practice for Monitoring the Calibration of Ultraviolet-Visible Spectrophotometers whose Spectral Bandwidth does not Exceed 2 nm |
| ASTM D 1385 : 2007 : R2018 : EDT 1 | Standard Test Method for Hydrazine in Water |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| ASTM E 2304 : 2003 : R2011 | Standard Practice for Use of a LiF Photo-Fluorescent Film Dosimetry System (Withdrawn 2020) |
| ISO 15557:1998 | Practice for use of a radiochromic film dosimetry system |
| ASTM D 859 : 2016 : REDLINE | Standard Test Method for Silica in Water |
| ASTM E 2304 : 2003 | Standard Practice for Use of a Lif Photo-Fluorescent Film Dosimetry System |
| BS ISO 15555:1998 | Practice for use of a ceric-cerous sulfate dosimetry system |
| 13/30282535 DC : 0 | BS ISO/ASTM 51401 - PRACTICE FOR USE OF A DICHROMATE DOSIMETRY SYSTEM |
| ASTM E 1900 : 2009 | GUIDE FOR DOSIMETRY IN RADIATION RESEARCH ON FOOD AND AGRICULTURAL PRODUCTS |
| ASTM D 2702 : 2005 | Standard Practice for Rubber Chemicals-Determination of Infrared Absorption Characteristics |
| ASTM D 3168 : 1985 : R2016 | Standard Practice for Qualitative Identification of Polymers in Emulsion Paints |
| ASTM D 3414 : 1998 | Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy |
| BS ISO 15561:1998 | Practice for use of a dichromate dosimetry system |
| ASTM D 1768 : 1989 : R2003 | Standard Test Method for Sodium Alkylbenzene Sulfonate in Synthetic Detergents by Ultraviolet Absorption |
| ASTM D 4282 : 2015 : REDLINE | Standard Test Method for Determination of Free Cyanide in Water and Wastewater by Microdiffusion |
| ASTM D 3124 : 1998 : R2003 | Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry |
| ASTM D 6248 : 1998 : R2004 | Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry |
| GOST R 52714:2018 | Motor gasolines. Determination of individual and group hydrocarbon composition by capillary gas сhromatography method |
| ASTM D 1385 : 2007 : R2013 : EDT 1 | Standard Test Method for Hydrazine in Water |
| ASTM D 2914 : 2015 : REDLINE | Standard Test Methods for Sulfur Dioxide Content of the Atmosphere (West-Gaeke Method) |
| ASTM D 7996 : 2015 | Standard Test Method for Measuring Visible Spectrum of Asphaltenes in Heavy Fuel Oils and Crude Oils by Spectroscopy in a Microfluidic Platform (Withdrawn 2024) |
| ASTM E 1401 : 2013 | PRACTICE FOR USE OF A DICHROMATE DOSIMETRY SYSTEM |
| ASTM D 3124 : 1998 | Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry |
| ASTM E 1866 : 1997 : R2002 | Standard Guide for Establishing Spectrophotometer Performance Tests |
| ISO/ASTM 51275:2013 | Practice for use of a radiochromic film dosimetry system |
| ASTM D 3133 : 2001 : R2005 | Standard Test Method for Quantitative Determination of Cellulose Nitrate in Alkyd Modified Lacquers by Infrared Spectrophotometry (Withdrawn 2008) |
| ASTM D 3082 : 2015 : REDLINE | Standard Test Method for Boron in Water |
| ASTM D 4193:2008 | Standard Test Method for Thiocyanate in Water |
| ASTM E 387:2004 | Standard Test Method for Estimating Stray Radiant Power Ratio of Dispersive Spectrophotometers by the Opaque Filter Method |
| ASTM D 5412 : 1993 : R2017 : EDT 1 | Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water |
| ASTM D 2621 : 1987 : R2000 | Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints |
| ASTM D 1687 : 2017 : REDLINE | Standard Test Methods for Chromium in Water |
| ASTM D 3168 : 1985 : R1999 | Standard Practice for Qualitative Identification of Polymers in Emulsion Paints |
| ASTM E 1615 : 2016 : REDLINE | Standard Test Method for Iron in Trace Quantities Using the FerroZine Method |
| ASTM D 1768 : 1989 : R1995 : EDT 1 | Standard Test Method for Sodium Alkylbenzene Sulfonate in Synthetic Detergents by Ultraviolet Absorption |
| ASTM E 685 : 1993 | Standard Practice for Testing Fixed-Wavelength Photometric Detectors Used in Liquid Chromatography |
| ASTM D 3650 : 1993 : R2006 | Standard Test Method for Comparison of Waterborne Petroleum Oils By Fluorescence Analysis |
| ASTM D 5463 : 2013-03 | GUIDE FOR USE OF TEST KITS TO MEASURE INORGANIC CONSTITUENTS IN WATER |
| ASTM D 2269 : 2010 | Standard Test Method for Evaluation of White Mineral Oils by Ultraviolet Absorption |
| ASTM D 2036 : 2009 : R2015 | Standard Test Methods for Cyanides in Water |
| ISO 15561:1998 | Practice for use of a dichromate dosimetry system |
| ISO 15558:1998 | Practice for use of a polymethylmethacrylate dosimetry system |
| AASHTO T 290 : 1995 | METHOD OF TEST FOR DETERMINING WATER-SOLUBLE SULFATE ION CONTENT IN SOIL |
| BS ISO 15554:1998 | Practice for dosimetry in gamma irradiation facilities for food processing |
| ISO 15565:1998 | Practice for use of a radiochromic liquid dosimetry system |
| DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
| ASTM D 6248 : 1998 | Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry |
| 03/310937 DC : DRAFT JUNE 2003 | EN 2436-6 - AEROSPACE SERIES - PAINTS AND VARNISHES - CORROSION RESISTANT CHROMATE FREE TWO COMPONENT COLD CURING PRIMER - PART 6: HIGH CORROSION RESISTANCE FOR MILITARY APPLICATION |
| BS ISO 15565:1998 | Practice for use of a radiochromic liquid dosimetry system |
| ASTM E 2056 : 2004 | Standard Practice for Qualifying Spectrometers and Spectrophotometers for Use in Multivariate Analyses, Calibrated Using Surrogate Mixtures |
| ASTM D 1840 : 2007 | Standard Test Method for Naphthalene Hydrocarbons in Aviation Turbine Fuels by Ultraviolet Spectrophotometry |
| ASTM D 5086 : 2001 : R2008 | Standard Test Method for Determination of Calcium, Magnesium, Potassium, and Sodium in Atmospheric Wet Deposition by Flame Atomic Absorption Spectrophotometry |
| ASTM D 2036 : 2009 | Standard Test Methods for Cyanides in Water |
| ASTM D 3414 : 1998 : R2004 | Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy |
| ASTM D 3414 : 1998 : R2011 : EDT 1 | Standard Test Method for Comparison of Waterborne Petroleum Oils by Infrared Spectroscopy (Withdrawn 2018) |
| ASTM D 3124 : 1998 : R2011 | Standard Test Method for Vinylidene Unsaturation in Polyethylene by Infrared Spectrophotometry |
| ASTM D 1252 : 2006 | Standard Test Methods for Chemical Oxygen Demand (Dichromate Oxygen Demand) of Water |
| ASTM D 1068 : 2015 : REDLINE | Standard Test Methods for Iron in Water |
| ASTM E 394 : 2015 : REDLINE | Standard Test Method for Iron in Trace Quantities Using the 1,10-Phenanthroline Method |
| ASTM D 3867 : 2016 : REDLINE | Standard Test Methods for Nitrite-Nitrate in Water |
| ASTM D 2703 : 1995 | Standard Practice for Rubber Chemicals-Determination of Ultraviolet Absorbance Characteristics (Withdrawn 2000) |
| GOST 849:2018 | Primary nickel. SpecificationsE |
| ASTM D 1252 : 2006 : R2012 | Standard Test Methods for Chemical Oxygen Demand (Dichromate Oxygen Demand) of Water |
| ASTM D 2702 : 2005 : R2011 | Standard Practice for Rubber Chemicals—Determination of Infrared Absorption Characteristics |
| ISO 15555:1998 | Practice for use of a ceric-cerous sulfate dosimetry system |
| 14/30315837 DC : 0 | BS ISO/ASTM 51026 - PRACTICE FOR USING THE FRICKE REFERENCE-STANDARD DOSIMETRY SYSTEM |
| ASTM E 1655 : 2017 : REDLINE | Standard Practices for Infrared Multivariate Quantitative Analysis |
| ISO/ASTM 51401:2013 | Practice for use of a dichromate dosimetry system |
| ASTM D 2621 : 1987 : R2005 | Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints |
| ASTM D 516 : 2016 : REDLINE | Standard Test Method for Sulfate Ion in Water |
| ASTM E 2056 : 2004 : R2016 | Standard Practice for Qualifying Spectrometers and Spectrophotometers for Use in Multivariate Analyses, Calibrated Using Surrogate Mixtures |
| DIN 51451:2004-09 | TESTING OF PETROLEUM PRODUCTS AND RELATED PRODUCTS - ANALYSIS BY INFRARED SPECTROMETRY - GENERAL WORKING PRINCIPLES |
| ASTM C 1580 : 2015 : REDLINE | Standard Test Method for Water-Soluble Sulfate in Soil |
| MIL P 7788 : F | PANEL, INFORMATION INTEGRALLY ILLUMINATED |
| ASTM D 4763 : 2006 : R2012 | Standard Practice for Identification of Chemicals in Water by Fluorescence Spectroscopy |
| ASTM E 512 : 1994 : R2015 | Standard Practice for Combined, Simulated Space Environment Testing of Thermal Control Materials with Electromagnetic and Particulate Radiation |
| MIL P 23377 : G | PRIMER COATING, EPOXY, HIGH SOLIDS |
| ASTM D 2269 : 2010 : R2015 | Standard Test Method for Evaluation of White Mineral Oils by Ultraviolet Absorption |
| NACE TM 03 99 : 2005 | Standard Test Method for Phosphonate in Brine |
| ASTM E 424 : 1971 : R2007 | Standard Test Methods for Solar Energy Transmittance and Reflectance (Terrestrial) of Sheet Materials |
| ASTM D 2330 : 2002 | Standard Test Method for Methylene Blue Active Substances (Withdrawn 2011) |
| ASTM D 3650 : 1993 : R1999 | Standard Test Method for Comparison of Waterborne Petroleum Oils By Fluorescence Analysis |
| ASTM D 3594 : 1993 : R2013 | Standard Test Method for Copolymerized Ethyl Acrylate In Ethylene-Ethyl Acrylate Copolymers (Withdrawn 2019) |
| ASTM D 6187 : 1997 | Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Laser-Induced Fluorescence |
| ASTM E 424 : 1971 : R2001 | Standard Test Methods for Solar Energy Transmittance and Reflectance (Terrestrial) of Sheet Materials |
| ASTM E 60 : 2011 : R2016 | Standard Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry |
| ISO/ASTM 51026:2015 | Practice for using the Fricke dosimetry system |
| ASTM D 2621 : 1987 : R1995 : EDT 1 | Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints |
| ASTM D 1426 : 2015 : REDLINE | Standard Test Methods for Ammonia Nitrogen In Water |
| ASTM D 1385 : 2007 | Standard Test Method for Hydrazine in Water |
| ASTM D 6248 : 1998 : R2012 : EDT 1 | Standard Test Method for Vinyl and Trans Unsaturation in Polyethylene by Infrared Spectrophotometry (Withdrawn 2021) |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM E 1275 : 2013 | PRACTICE FOR USE OF A RADIOCHROMIC FILM DOSIMETRY SYSTEM |
| ASTM G 214 : 2016 : REDLINE | Standard Test Method for Integration of Digital Spectral Data for Weathering and Durability Applications |
| ASTM D 1252 : 2006 : R2012 : EDT 1 | Standard Test Methods for Chemical Oxygen Demand (Dichromate Oxygen Demand) of Water |
| ASTM D 5086 : 2001 : R2013 | Standard Test Method for Determination of Calcium, Magnesium, Potassium, and Sodium in Atmospheric Wet Deposition by Flame Atomic Absorption Spectrophotometry |
| ASTM D 6342 : 20121 | Standard Practice for Polyurethane Raw Materials: Determining Hydroxyl Number of Polyols by Near Infrared (NIR) Spectroscopy |
| ASTM E 2808 : 2011 | Standard Guide for Microspectrophotometry and Color Measurement in Forensic Paint Analysis |
| ASTM E 2193 : 2016 : REDLINE | Standard Test Method for Ultraviolet Transmittance of Monoethylene Glycol (using Ultraviolet Spectrophotometry) |
| ASTM E 903 : 2012 | Standard Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres |
| ASTM E 1540 : 2004 | PRACTICE FOR USE OF A RADIOCHROMIC LIQUID DOSIMETRY SYSTEM |
| ASTM E 512 : 1994 : R2004 | Standard Practice for Combined, Simulated Space Environment Testing of Thermal Control Materials with Electromagnetic and Particulate Radiation |
| ASTM E 512 : 1994 : R1999 | Standard Practice for Combined, Simulated Space Environment Testing of Thermal Control Materials with Electromagnetic and Particulate Radiation |
| ASTM D 3591 : 2017 : REDLINE | Standard Test Method for Determining Logarithmic Viscosity Number of Poly(Vinyl Chloride) (PVC) in Formulated Compounds |
| ASTM E 169 : 2016 : REDLINE | Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis |
| ASTM E 958 : 2013 : REDLINE | Standard Practice for Estimation of the Spectral Bandwidth of Ultraviolet-Visible Spectrophotometers |
| ASTM E 168 : 2016 | Standard Practices for General Techniques of Infrared Quantitative Analysis |
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.