Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

09-30-2022

Publisher

American Society for Testing and Materials

1.1This test method describes the use of linear controlled-rate-of-loading in three-point bending to determine the elastic modulus of isotropic specimens in the form of rectangular bars using a thermomechanical analyzer (TMA).

Note 1:This method is intended to provide results similar to those of Test Methods D790 or D5934 but is performed on a thermomechanical analyzer using smaller test specimens. Until the user demonstrates equivalence, the results of this method shall be considered independent and unrelated to those of Test Methods D790 or D5934.

1.2This test method provides a means for determining the elastic modulus within the linear region of the stress-strain curves (see Fig. 1). This test is conducted under isothermal temperature conditions from –100 °C to 300 °C.

FIG. 1Stress-Strain Curve (Linear Region)

1.3Typical test specimens are in the form of thin strips 0.5 mm in thickness, 1.5 mm in width, and 6 mm in length. The size of the test specimen is limited by the distance between the supports used in the three-point bending mode of operation, commonly 0.5 cm.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	E 37
DocumentType	Test Method
Pages	6
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM E 2769 : 2018

ASTM E 473 : 2022 : REV D	Standard Terminology Relating to Thermal Analysis and Rheology
ASTM E 2092 : 2023	Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM E 2113 : 2023	Standard Test Method for Length Change Calibration of Thermomechanical Analyzers
ASTM E 1142 : 2022 : REV C	Standard Terminology Relating to Thermophysical Properties
ASTM E 473 : 2023 : REV A	Standard Terminology Relating to Thermal Analysis and Rheology
ASTM E 1363 : 2023	Standard Test Method for Temperature Calibration of Thermomechanical Analyzers
ASTM E 2113 : 2018	Standard Test Method for Length Change Calibration of Thermomechanical Analyzers
ASTM E 1142 : 2022 : REV B	Standard Terminology Relating to Thermophysical Properties
ASTM E 1363 : 2018	Standard Test Method for Temperature Calibration of Thermomechanical Analyzers
ASTM E 1142 : 2023	Standard Terminology Relating to Thermophysical Properties
ASTM E 473 : 2023 : REV B	Standard Terminology Relating to Thermal Analysis and Rheology
ASTM E 473 : 2023	Standard Terminology Relating to Thermal Analysis and Rheology
ASTM E 1142 : 2023 : REV B	Standard Terminology Relating to Thermophysical Properties
ASTM E 2092 : 2018 : REV A	Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM E 1142 : 2023 : REV A	Standard Terminology Relating to Thermophysical Properties