• There are no items in your cart

ASTM E 3044/E3044M : 2016 : EDT 1

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Ultrasonic Testing of Polyethylene Butt Fusion Joints
Available format(s)

Hardcopy , PDF

Superseded date

03-09-2022

Language(s)

English

Published date

09-19-2016

1.1This standard practice establishes procedures for ultrasonic testing (UT) of butt fusion joints in polyethylene pipe. Although high density polyethylene (HDPE) and medium density polyethylene (MDPE) materials are most commonly used, the procedures described may apply to other types of polyethylene.

Note 1:The notes in this specification are for information only and shall not be considered part of this specification.

Note 2:This standard references HDPE and MDPE for pipe applications as defined by Specification D3350.

1.2This standard practice does not address ultrasonic examination of electrofusion joints (coupling joints), socket joints, or saddles.

1.3This practice provides two ultrasonic examination procedures. Each has its own merits and requirements for examination and shall be selected as agreed upon in a contractual document.

1.3.1Examination Procedure A, Time of Flight Diffraction (TOFD), uses a pair of probes, one transmitting and the other receiving. The procedure requires access to both sides of the joint from one surface. Provided that position encoding is used, the procedure can be conducted by semi-automated or automated means that provide recoded imaging.

1.3.2Examination Procedure B, Phased Array Ultrasonic Testing (PAUT), uses low velocity refracting wedges or water gaps to produce angled compression mode pulses. The procedure can be applied where access is limited to one side of the joint from one surface. Provided that position encoding is used, the procedure can be conducted by semi-automated or automated means that provide recoded imaging.

1.4The practice is intended to be used on thicknesses of 9 to 60 mm (0.375 to 2.4 in.) and diameters 100 mm (4 in.) and greater. Greater and lesser thicknesses and lesser diameters may be tested using this standard practice if the technique can be demonstrated to provide adequate detection on mockups of the same wall thickness and geometry.

1.5This practice does not specify acceptance criteria.

1.6The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 07
DocumentType
Standard Practice
Pages
9
ProductNote
Subsection 5.2 corrected editorially in September 2016.
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 3170/E3170M : 2018 Standard Practice for Phased Array Ultrasonic Testing of Polyethylene Electrofusion Joints
ASTM E 543 : 2021 Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 3167/E3167M : 2018 Standard Practice for Conventional Pulse-Echo Ultrasonic Testing of Polyethylene Electrofusion Joints

ASTM E 1316 : 2015 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2020 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2017 Standard Terminology for Nondestructive Examinations
ASTM F 2620 : 2020 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM E 543 : 2021 Standard Specification for Agencies Performing Nondestructive Testing
ASTM D 3350 : 2000 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM E 1316 : 2018 Standard Terminology for Nondestructive Examinations
ASTM F 2620 : 2020 : REV A : EDT 1 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 3350 : 2021 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM E 1316 : 2015 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2019 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV A Standard Terminology for Nondestructive Examinations
ASTM D 3350 : 2014 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM E 1316 : 2000 Standard Terminology for Nondestructive Examinations
ASTM E 2373 : 2004 Standard Practice for Use of the Ultrasonic Time of Flight Diffraction (TOFD) Technique
ASTM E 543 : 2015 Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 1316 : 2016 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV D Standard Terminology for Nondestructive Examinations
ASTM E 2700 : 2020 Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays
ASTM E 1316 : 2014 : EDT 1 Standard Terminology for Nondestructive Examinations
ASTM F 2620 : 2006 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM E 1316 : 2021 : REV B Standard Terminology for Nondestructive Examinations
ASTM F 2620 : 2020 : REV A Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM E 1316 : 2017 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2016 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 2700 : 2009 Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays
ASTM E 1316 : 2002 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 : REV C Standard Terminology for Nondestructive Examinations

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.