ASTM E 55 : 2011 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
06-29-2023
English
09-08-2017
CONTAINED IN VOL. 03.05, 2017 Defines the sampling, for the determination of chemical composition, of nonferrous metals and alloys that have been reduced to their final form by mechanical working; that is, by such means as rolling, drawing, and extruding.
1.1This practice covers the sampling, for the determination of chemical composition (Note 1), of nonferrous metals and alloys that have been reduced to their final form by mechanical working; that is, by such means as rolling, drawing, and extruding.
1.1.1Refer to Practice E255 for copper and copper alloys.
Note 1:The selection of correct portions of material and the preparation of a representative sample from such portions are necessary prerequisites to every analysis, the analysis being of no value unless the sample actually represents the average composition of the material from which it was selected.
1.2In special cases, when agreed upon by the purchaser and the manufacturer, the heat analysis may be accepted as representative of the composition of the finished product. In such cases, the identity of each heat of metal should be maintained through each stage of the manufacturing process to the final form. This method of sampling is not intended to apply under these conditions.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
E 01
|
| DocumentType |
Standard Practice
|
| Pages |
3
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM E 2823 : 2017 | Standard Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Mass Spectrometry (Performance-Based) |
| ASTM F 467M : 2006 : REV A : R2018 | Standard Specification for Nonferrous Nuts for General Use (Metric) |
| ASTM E 581 : 2017 : REV A : R2022 : EDT 1 | Standard Test Methods for Chemical Analysis of Manganese-Copper Alloys |
| ASTM E 536 : 2016 | Standard Test Methods for Chemical Analysis of Zinc and Zinc Alloys |
| ASTM B 815 : 2002 : R2016 | Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy<brk/> (UNS R31233) Rod |
| ASTM F 468M : 2006 : R2018 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric) |
| ASTM E 439 : 2017 | Standard Test Methods for Chemical Analysis of Beryllium |
| ASTM B 236 : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| ASTM B 317/B317M : 2007 : R2015 : EDT 1 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM F 468 : 2016 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use |
| ASTM F 3042 : 2013 : R2018 | Standard Specification for Nonferrous Hex Socket, Slotted Headless, and Square Head Set Screws |
| ASTM B 649 : 2021 | Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy and Cr-Ni-Fe-N <brk/>Low-Carbon Alloy Bar and Wire, Ni-Cr-Fe-Mo-N Alloy Wire, and Ni-Fe-Cr-Mo-N Alloy Bar |
| ASTM B 880 : 2014 : R2019 | Standard Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys |
| ASTM B 69 : 2021 | Standard Specification for Rolled Zinc |
| ASTM B 906 : 2022 | Standard Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip |
| ASTM B 476 : 2021 | Standard Specification for General Requirements for Wrought Precious Metal Electrical Contact Materials |
| ASTM B 843 : 2018 : EDT 1 | Standard Specification for Magnesium Alloy Anodes for Cathodic Protection |
| ASTM B 335 : 2003 : R2018 | Standard Specification for Nickel-Molybdenum Alloy Rod |
| ASTM B 574 : 2018 | Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod |
| ASTM E 1834 : 2018 | Standard Test Method for Analysis of Nickel Alloys by Graphite Furnace Atomic Absorption Spectrometry |
| ASTM F 901 : 2020 | Standard Specification for Aluminum Transmission Tower Bolts and Nuts |
| ASTM B 599 : 2020 | Standard Specification for Nickel-Iron-Chromium-Molybdenum-Niobium Stabilized Alloy Plate, Sheet, and Strip |
| ASTM B 581 : 2017 | Standard Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Rod |
| ASTM B 90/B90M : 2021 | Standard Specification for Magnesium-Alloy Sheet and Plate |
| ASTM E2972 : 2015(2019) | Standard Guide for Production, Testing, and Value Assignment of In-House Reference Materials for Metals, Ores, and Other Related Materials |
| ASTM B 91 : 2017 | Standard Specification for Magnesium-Alloy Forgings |
| ASTM B 107/B107M : 2013 : R2021 | Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire |
| ASTM E 2594 : 2020 | Standard Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based) |
| ASTM B 479 : 2019 | Standard Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier, Food Contact, and Other Applications |
| ASTM E 396 : 2017 | Standard Test Methods for Chemical Analysis of Cadmium |
| ASTM B 32 : 2020 | Standard Specification for Solder Metal |
| ASTM B 774/B774M : 2021 | Standard Specification for Low Melting Point Alloys and Solders |
| ASTM B 233 : 1997 : R2021 | Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes |
| ASTM B 572 : 2006 : R2016 | Standard Specification for UNS N06002, UNS N06230, UNS N12160, and UNS R30556 Rod |
| ASTM F 467 : 2013 : R2018 | Standard Specification for Nonferrous Nuts for General Use |
| ASTM B 236M : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) (Metric) (Withdrawn 2024) |
| ASTM B 949 : 2018 | Standard Specification for General Requirements for Zinc and Zinc Alloy Products |
| ASTM B 907 : 2016 : R2021 | Standard Specification for Zinc, Tin and Cadmium Base Alloys Used as Solders |
| ASTM E 1277 : 2022 | Standard Test Method for Analysis of Zinc-5 % Aluminum-Mischmetal Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry |
| ASTM E 135 : 2021 : REV A | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
| ASTM E 255 : 1991 : R1997 | Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition |
| ASTM E 135 : 2003 : REV B | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
| ASTM E 135 : 2002 : REV A | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
| ASTM E 135 : 2021 | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
| ASTM E 135 : 2003 | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
| ASTM E 135 : 2003 : REV C | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
| ASTM E 135 : 2020 : REV B | Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.