• There are no items in your cart

ASTM E 999 : 2015 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing
Available format(s)

PDF

Superseded date

08-05-2020

Language(s)

English

Published date

06-01-2015

CONTAINED IN VOL. 03.03, 2017 Identifies guidelines which can be used in maintenance and control of industrial radiographic film processing materials and equipment.

1.1This guide2 establishes guidelines that may be used for the control and maintenance of industrial radiographic film processing equipment and materials. Effective use of these guidelines aid in controlling the consistency and quality of industrial radiographic film processing.

1.2Use of this guide is limited to the processing of films for industrial radiography. This guide includes procedures for wet-chemical processes and dry processing techniques.

1.3The necessity of applying specific control procedures such as those described in this guide is dependent, to a certain extent, on the degree to which a facility adheres to good processing practices as a matter of routine procedure.

1.4If a nondestructive testing agency as described in Practice E543 is used to perform the examination, the testing agency shall meet the requirements of Practice E543.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of federal and local codes prior to use.

Committee
E 07
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM E 1735 : 2007 : R2014 Standard Test Method for Determining Relative Image Quality of Industrial Radiographic Film Exposed to X-Radiation from 4 to 25 MeV
ASTM E 1030/E1030M : 2015 : REDLINE Standard Practice for Radiographic Examination of Metallic Castings
ASTM E 1030 : 2005 Standard Test Method for Radiographic Examination of Metallic Castings
ASTM E 592 : 2015 : REDLINE Standard Guide to Obtainable ASTM Equivalent Penetrameter Sensitivity for Radiography of Steel Plates <fraction><num>1</num><den>4 </den></fraction> to 2 in. (6 to 51 mm) Thick with X-Rays and 1 to 6 in. (25 to 152 mm) Thick with <brk/>Cobalt-60
API TR 17TR8 : 2018 HIGH-PRESSURE HIGH-TEMPERATURE DESIGN GUIDELINES
ASTM E 1030 : 2005 : R2011 Standard Test Method for Radiographic Examination of Metallic Castings
ASTM C 1175 : 1999 : REV A : R2004 Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics
ASTM E 543 : 2015 : REDLINE Standard Specification for Agencies Performing Nondestructive Testing
ASTM C 1175 : 1999 : REV A : R2010 Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics (Withdrawn 2018)
ASTM E 1114 : 2009 : EDT 1 Standard Test Method for Determining the Size of Iridium-192 Industrial Radiographic Sources
ASTM E 1742/E1742M : 2018 : REDLINE Standard Practice for Radiographic Examination
ASTM E 94 : 2004 Standard Guide for Radiographic Examination
ASTM E 1161 : 2009 : R2014 Standard Practice for Radiologic Examination of Semiconductors and Electronic Components
18/30338016 DC BS ISO 20890-6. In-service inspections for primary coolant circuit components of light water reactors Part 6. Radiographic testing
ASTM E 1114 : 2009 : R2014 Standard Test Method for Determining the Size of Iridium-192 Industrial Radiographic Sources
ASTM E 1735 : 2007 Standard Test Method for Determining Relative Image Quality of Industrial Radiographic Film Exposed to X-Radiation from 4 to 25 MeV
ASTM E 1114:2009 Standard Test Method for Determining the Size of Iridium-192 Industrial Radiographic Sources
ASTM E 746 : 2018 : REDLINE Standard Practice for Determining Relative Image Quality Response of Industrial Radiographic Imaging Systems
ABS 0014 : 2018 GUIDE FOR NONDESTRUCTIVE INSPECTION OF HULL WELDS
ASTM E 2104 : 2015 : REDLINE Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components
ASTM E 94/E94M : 2017 : REDLINE Standard Guide for Radiographic Examination Using Industrial Radiographic Film
ASTM E 94 : 2004 : R2010 Standard Guide for Radiographic Examination
ASTM E 1161 : 2009 Standard Practice for Radiologic Examination of Semiconductors and Electronic Components
ASTM C 1175 : 1999 : REV A Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics

ASTM E 1254 : 2013 Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
ISO 18917:1999 Photography Determination of residual thiosulfate and other related chemicals in processed photographic materials Methods using iodine-amylose, methylene blue and silver sulfide
ASTM E 543 : 2015 : REDLINE Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 1079 : 2016 : REDLINE Standard Practice for Calibration of Transmission Densitometers
ISO 11699-2:1998 Non-destructive testing Industrial radiographic films Part 2: Control of film processing by means of reference values

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.