• ASTM F 1201 : 1988 : R2010

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Specification for Fluid Conditioner Fittings in Piping Applications Above 0°F

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-11-2014

    Language(s):  English

    Published date:  05-01-2010

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 01.07, 2017 Describes the minimum requirements for pressure-retaining components of fluid conditioner fittings.

    Scope - (Show below) - (Hide below)

    1.1 This specification provides the minimum requirements for pressure-retaining components of fluid conditioner fittings. It addresses the pressure-retaining component design, fabrication, rating, marking, and testing.

    1.2 This specification is not intended to override any of the present fluid conditioner fitting specifications specific to devices such as strainers, filters, and traps but should be used for devices for which a specific specification does not apply.

    1.3 This specification provides sufficient requirements to allow a fluid conditioner fitting to be used in the marine environment.

    1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

    1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee F 25
    Document Type Standard
    Product Note Reconfirmed 2010
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASME B16.1 : 2015 Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250
    ASME B31.1 : 2016 POWER PIPING
    ASME B16.15 : 2013 CAST COPPER ALLOY THREADED FITTINGS: CLASSES 125 AND 250
    MSS SP 67 : 2017 BUTTERFLY VALVES
    ASME PV CODE 9 : 2017 BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS
    ASME B16.4 : 2016 GRAY IRON THREADED FITTINGS: CLASSES 125 AND 250
    ASME B16.25 : 2012 BUTTWELDING ENDS
    MSS SP 51 : 2012 CLASS 150LW CORROSION RESISTANT FLANGES AND CAST FLANGED FITTINGS
    ANSI B2.1 : LATEST PIPE THREADS (EXCEPT DRYSEAL)
    ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
    ASTM D 93 : 2016-07 TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
    MSS SP 61 : 2013 PRESSURE TESTING OF VALVES
    ASME PV CODE 8 DIV 2 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES
    MSS SP 44 : 2016 STEEL PIPELINE FLANGES
    ASME B16.5 : 2017 PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
    ASME B16.24 : 2016 CAST COPPER ALLOY PIPE FLANGES, FLANGED FITTINGS, AND VALVES: CLASSES 150, 300, 600, 900, 1500, AND 2500
    ASME B16.11 : 2016 FORGED FITTINGS, SOCKET-WELDING AND THREADED
    ASME B16.3 : 2016 MALLEABLE IRON THREADED FITTINGS: CLASSES 150 AND 300
    ASME PV CODE 8 DIV 3 : 2017 BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective