• There are no items in your cart

ASTM F 1717 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model
Available format(s)

Hardcopy , PDF

Superseded date

05-17-2021

Language(s)

English

Published date

08-22-2018

These test methods cover the materials and methods for the static and fatigue testing of spinal implant assemblies in a vertebrectomy model.

1.1These test methods cover the materials and methods for the static and fatigue testing of spinal implant assemblies in a vertebrectomy model. The test materials for most combinations of spinal implant components can be specific, depending on the intended spinal location and intended method of application to the spine.

1.2These test methods are intended to provide a basis for the mechanical comparison among past, present, and future spinal implant assemblies. They allow comparison of spinal implant constructs with different intended spinal locations and methods of application to the spine. These test methods are not intended to define levels of performance, since sufficient knowledge is not available to predict the consequences of the use of a particular device.

1.3These test methods set out guidelines for load types and methods of applying loads. Methods for three static load types and one fatigue test are defined for the comparative evaluation of spinal implant assemblies.

1.4These test methods establish guidelines for measuring displacements, determining the yield load, and evaluating the stiffness and strength of the spinal implant assembly.

1.5Some spinal constructs may not be testable in all test configurations.

1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 04
DocumentType
Test Method
Pages
21
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 2624 : 2012 : R2016 Standard Test Method for Static, Dynamic, and Wear Assessment of Extra-Discal Single Level Spinal Constructs
ASTM F 2624 : 2012 : R2020 Standard Test Method for Static, Dynamic, and Wear Assessment of Extra-Discal Single Level Spinal Constructs
ASTM F 2193 : 2020 Standard Specifications and Test Methods for Components Used in the Surgical Fixation of the Spinal Skeletal System
ASTM F 3292 : 2019 Standard Practice for Inspection of Spinal Implants Undergoing Testing

ASTM F 1582 : 1998 : R2016 Standard Terminology Relating to Spinal Implants
ASTM E 177 : 1990 : REV A : R1996 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM F 2077 : 2003 Test Methods For Intervertebral Body Fusion Devices
ASTM F 1582 : 1998 : R2003 Standard Terminology Relating to Spinal Implants
ASTM E 6 : 2002 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM F 2077 : 2017 Test Methods For Intervertebral Body Fusion Devices
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM F 2077 : 2000 Test Methods For Intervertebral Body Fusion Devices
ASTM F 2077 : 2018 Test Methods For Intervertebral Body Fusion Devices
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM F 2077 : 2001 Test Methods For Intervertebral Body Fusion Devices
ASTM F 2077 : 2011 Test Methods For Intervertebral Body Fusion Devices
ASTM F 1582 : 1998 : R2011 Standard Terminology Relating to Spinal Implants
ASTM F 1582 : 1998 Standard Terminology Relating to Spinal Implants
ASTM F 2077 : 2014 Test Methods For Intervertebral Body Fusion Devices

View more information
US$108.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.