ASTM F 1901 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems
Available format(s)
Hardcopy , PDF
Superseded date
09-10-2022
Language(s)
English
Published date
08-30-2016
1.1This specification covers requirements for polyethylene (PE) pipe and fittings for nonpressure roof drain systems.
1.2This specification covers pipe and fittings intended for normal residential and commercial uses and is not intended for use in unusual corrosive conditions.
Note 1:Before installing pipe for waste disposal use, the approval of the cognizant building code authority shall be obtained as conditions not found in normal use or temperatures approaching 140°F (60°C) may be encountered.
1.3Pipe is produced in dimensions based on outside diameters of 32 mm (1.250 in.) and larger in accordance with Specification F714.
1.4The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.
1.5Pipe and fittings are joined by the heat-fusion method, by the electrofusion method, or by using mechanical joints (excluding insert fittings) recommended by the manufacturer.
1.6In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10). In all cases, the values given in parentheses are provided for information only.
1.7The following safety hazards caveat pertains only to the test method, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM F 2021 : 2017 | Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems |
| ASTM F 2021 : 2017 : R2022 | Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 714 : 2013 : R2019 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 477 : 2014 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 2444 : 1999 : R2010 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 2444 : 2019 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 4976 : 2006 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 4976 : 2000 : REV B | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM F 2620 : 2011 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM F 2620 : 2020 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM F 477 : 2002 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM D 2444 : 2017 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 3311 : 1992 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 2412 : 2011 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2000 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4976 : 2004 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 2412 : 2002 : R2008 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM F 2620 : 2011 : EDT 1 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 3311 : 2006 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 4976 : 2004 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM F 2620 : 2019 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM F 714 : 2021 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| ASTM F 2620 : 2020 : REV A : EDT 1 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 3350 : 2008 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 1290 : 1998 : REV A : R2004 | Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings |
| ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2412 : 2010 : REV A | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3311 : 2009 : REV A | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 3350 : 2002 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 2620 : 2013 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 543 : 2021 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3311 : 2008 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 3311 : 2002 : EDT 1 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2444 : 2021 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 714 : 2022 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| ASTM F 1498 : 2008 | Standard Specification for Taper Pipe Threads 60<span class='unicode'>°</span> for Thermoplastic Pipe and Fittings |
| ASTM F 714 : 2021 : REV A | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4976 : 2012 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM F 477 : 2014 : R2021 | Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| ASTM D 2412 : 1996 : REV A | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2004 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3311 : 1994 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 3350 : 2002 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3350 : 2012 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3350 : 2001 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2412 : 2002 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3311 : 2011 : R2016 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 4976 : 2002 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 3311 : 2017 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 3350 : 2012 : EDT 1 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 1498 : 2008 : R2012 : EDT 1 | Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings |
| ASTM D 3311 : 2002 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM F 2620 : 2012 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 3311 : 2006 : REV A | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM F 2620 : 2006 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 2444 : 1999 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 2412 : 2021 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3311 : 2011 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 543 : 2020 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D 3350 : 2010 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 1290 : 1998 : REV A : R2011 | Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 2444 : 1999 : R2005 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 3350 : 2006 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 2620 : 2020 : REV A | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 4976 : 2002 : EDT 1 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 3350 : 2010 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 1290 : 1998 : REV A | Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings |
| ASTM F 1498 : 2000 | Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings |
| ASTM D 3311 : 2009 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM F 2620 : 2020 : REV A : EDT 2 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 2412 : 2011 : R2018 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 2412 : 2010 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2005 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 2620 : 2009 : EDT 1 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 3311 : 2017 : R2021 | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.