• There are no items in your cart

ASTM F 22 : 2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Hydrophobic Surface Films by the Water-Break Test
Available format(s)

Hardcopy , PDF

Superseded date

05-24-2021

Language(s)

English

Published date

11-25-2013

This test method covers the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing environments.

1.1This test method covers the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing environments. When properly conducted, the test will enable detection of molecular layers of hydrophobic organic contaminants. On very rough or porous surfaces, the sensitivity of the test may be significantly decreased.

1.2The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are for information only.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 21
DocumentType
Test Method
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 2625 : 2020 Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method)
ASTM F 2661 : 2007 : R2015 Standard Test Method for Determining the Tribological Behavior and the Relative Lifetime of a Fluid Lubricant using the Spiral Orbit Tribometer
ASTM F 21 : 2020 Standard Test Method for Hydrophobic Surface Films by the Atomizer Test
ASTM A 380/A380M : 2017 Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
ASTM F 2664 : 2019 : EDT 1 Standard Guide for Assessing the Attachment of Cells to Biomaterial Surfaces by Physical Methods
ASTM D 2510 : 1994 : R2017 Standard Test Method for Adhesion of Solid Film Lubricants

ASTM D 2578 : 2009 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 7490 : 2008 Standard Test Method for Measurement of the Surface Tension of Solid Coatings, Substrates and Pigments using Contact Angle Measurements
ASTM D 7334 : 2008 Standard Practice for Surface Wettability of Coatings, Substrates and Pigments by Advancing Contact Angle Measurement
ASTM D 2578 : 2008 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 1193 : 1977 : R1983 : EDT 1 Standard Specification for Reagent Water
ASTM D 5946 : 2004 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 2578 : 1999 : REV A Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 5946 : 2009 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 2578 : 2017 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 5946 : 1999 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 1193 : 2006 : R2011 Standard Specification for Reagent Water
ASTM D 5946 : 2001 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 7490 : 2013 Standard Test Method for Measurement of the Surface Tension of Solid Coatings, Substrates and Pigments using Contact Angle Measurements
ASTM D 1193 : 1991 Standard Specification for Reagent Water
ASTM D 7334 : 2008 : R2013 Standard Practice for Surface Wettability of Coatings, Substrates and Pigments by Advancing Contact Angle Measurement
ASTM D 2578 : 2004 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 5946 : 2017 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 1193 : 1970 Standard Specification For Reagent Water
ASTM D 1193 : 2006 Standard Specification for Reagent Water
ASTM D 1193 : 1999 Standard Specification for Reagent Water
ASTM D 1193 : 2006 : R2018 Standard Specification for Reagent Water
ASTM D 2578 : 2004 : REV A Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.