• There are no items in your cart

ASTM F 2767 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution
Available format(s)

Hardcopy , PDF

Superseded date

11-13-2023

Language(s)

English

Published date

04-16-2018

1.1This specification covers polyamide- 12 electrofusion fittings for use with outside diameter-controlled polyamide- 12 pipe, covered by Specification F2785. Requirements for materials, workmanship, and testing performance are included. Where applicable in this specification “pipe” shall mean “pipe” or “tubing.”

1.2Polyamide 12 electrofusion fittings are intended for use in polyamide 12 systems only. As per the manufacturer’s recommendations, no cross fusion between PA12, PA11 and PE is permitted.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4The following safety hazards caveat pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 17
DocumentType
Standard
Pages
11
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 3524/F3524M : 2023 Standard Specification for Polyamide-12 (PA12) Line Pipe
ASTM F 2785 : 2018 : REV A Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 6779 : 2002 Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2020 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM F 905 : 2004 : R2018 Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
ASTM D 2122 : 1998 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 1598 : 2015 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2015 : REV A Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2023 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 2785 : 2020 : EDT 1 Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
ASTM D 1598 : 1997 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 4066 : 2013 : R2019 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 1599 : 2014 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 4066 : 1994 : REV B Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 6779 : 2023 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 2122 : 2022 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2021 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM F 905 : 2004 : R2022 Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
ASTM D 6779 : 2016 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2021 Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM F 2785 : 2009 Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
ASTM F 2785 : 2021 Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
ASTM F 2785 : 2020 Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
ASTM D 1599 : 1999 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 2122 : 2015 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM F 2785 : 2018 Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.