• There are no items in your cart

ASTM F 2790 : 2010 : R2019 : EDT 1

Current
Current

The latest, up-to-date edition.

Standard Practice for Static and Dynamic Characterization of Motion Preserving Lumbar Total Facet Prostheses
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

12-18-2019

1.1This practice provides guidance for the static and dynamic testing of Lumbar Total Facet Prostheses (FPs). These implants are intended to allow motion and lend support to one or more functional spinal unit(s) through replacement of the natural facets.

1.2These test methods are intended to provide a basis for the mechanical comparison among past, present, and future non-biologic FPs. These test methods allow comparison of devices with different methods of application to the lumbar spine. These test methods are intended to enable the user to mechanically compare devices and do not purport to provide performance standards for them.

1.3These test methods describe static and dynamic tests by specifying load types and specific methods of applying these loads.

1.4These test methods do not purport to address all clinically relevant failure modes for FPs, some of which will be device-specific. For example, these test methods do not address implant wear resistance under expected in vivo loads and motions. In addition, the biologic response to wear debris is not addressed in these test methods.

1.5Requirements are established for measuring displacements and evaluating the stiffness of an FP.

1.6Some devices may not be testable in all test configurations.

1.7The values stated in SI units are to be regarded as the standard with the exception of angular measurements, which may be reported in terms of either degrees or radians.

1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 04
DocumentType
Standard Practice
Pages
8
ProductNote
Editorial corrections were made throughout in December 2019.
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM F 3292 : 2019 Standard Practice for Inspection of Spinal Implants Undergoing Testing

ASTM E 468 : 1990 : R2004 Standard Practice for Presentation of Constant Amplitude Fatigue Test Results for Metallic Materials
ASTM E 6 : 2002 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 739 : 2023 Standard Guide for Statistical Analysis of Linear or Linearized Stress-Life (<emph type="bdit">S-N</emph>) and Strain-Life (ε-<emph type="bdit" >N</emph>) Fatigue Data (Withdrawn 2024)
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM E 6 : 2015 : EDT 3 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 739 : 2010 : R2015 Standard Practice for Statistical Analysis of Linear or Linearized Stress-Life (<emph type="bdit">S-N</emph>) and Strain-Life (ε-<emph type="bdit" >N</emph>) Fatigue Data
ASTM E 6 : 2023 : REV A Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 4 : 2021 Standard Practices for Force Calibration and Verification of Testing Machines
ASTM E 6 : 2015 : EDT 4 : REDLINE Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 468 : 2018 Standard Practice for Presentation of Constant Amplitude Fatigue Test Results for Metallic Materials
ASTM E 6 : 2015 : EDT 4 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 6 : 2023 Standard Terminology Relating to Methods of Mechanical Testing
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics

View more information
US$63.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.