• There are no items in your cart

ASTM F 2807 : 2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

11-01-2013

CONTAINED IN VOL. 08.04, 2018 Defines requirements and test methods for 1/2 in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA).

1.1This specification covers requirements and test methods for 1/2in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA). The multilayer pipe covered by this specification is intended for use in piping applications where the permeation and chemical resistance of polyamide (PA) compounds may be useful to protect the PE pipe layer, such as oil and gas producing applications that convey oil, dry or wet gas, and multiphase fluids.

Note 1Permeability and chemical resistance depends on the type of PA used. The PA layer delays but does not prevent liquid hydrocarbons effects. Therefore, the hydrocarbon chemical design factor for this multilayer pipe should be the same as for PE pipe layer—see X1.2.

1.2Electrofusion and mechanical joints are typically used for this multilayer pipe.

1.3Unless specified otherwise, all the pipe requirements in this standard are for the multilayer pipe.

1.4The PA layer is not taken into consideration for the design pressure of multilayer pipe meeting this specification. Design pressure rating is determined from the PE pipe layer alone—see Appendix X1.

1.5Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in figures and tables) shall not be considered as requirements of the standard.

1.7The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 17
DocumentType
Standard
Pages
7
ProductNote
Reconfirmed 2013
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

MIL-STD-129 Revision R:2014 Military Marking for Shipment and Storage
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 6779 : 2017 : REDLINE Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
PPI TR 3 : 2017 POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ASTM D 1603 : 2014 : REDLINE Standard Test Method for Carbon Black Content in Olefin Plastics
FED-STD-123 Revision H:2007 MARKING FOR SHIPMENT (CIVIL AGENCIES)
ASTM F 2619/F2619M : 2013 : REDLINE Standard Specification for High-Density Polyethylene (PE) Line Pipe
ISO 8510-2:2006 Adhesives Peel test for a flexible-bonded-to-rigid test specimen assembly Part 2: 180 peel
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2290 : 2016-12 TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
SAE J 2260 : 2004 NONMETALLIC FUEL SYSTEM TUBING WITH ONE OR MORE LAYERS

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.