• ASTM F 3016/F3016M : 2014

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Test Method for Surrogate Testing of Vehicle Impact Protective Devices at Low Speeds

    Available format(s):  Hardcopy, PDF

    Superseded date:  09-17-2019

    Language(s):  English

    Published date:  11-01-2014

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 15.08, 2015 Gives a range of impact speeds to be used with a 22 250-N [5000 lb] surrogate test vehicle.

    Scope - (Show below) - (Hide below)

    1.1This test method provides a range of impact speeds to be used with a 22 250-N [5000 lb] surrogate test vehicle. This test method establishes a range for penetration performance ratings. End users will be responsible for identifying the appropriate vehicle impact speed and penetration performance ratings in this test method to satisfy their specific needs.

    1.1.1In addition, end users may assign certification ratings for vehicle protective devices based on the test methodologies described herein. Test parameters are standardized to arrive at a common vehicle weight, enhance test realism and replication, and produce uniform rating designations.

    1.2Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

    1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee F 12
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ASTM F 2656 : 2007 Standard Test Method for Vehicle Crash Testing of Perimeter Barriers
    ASTM C 136 : 2006 Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
    ASTM D 2487 : 2006 : EDT 1 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
    SAE J 211-1 : 2014 INSTRUMENTATION FOR IMPACT TEST - PART 1 - ELECTRONIC INSTRUMENTATION
    ASTM D 2487 : 2010 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
    ASTM D 2487 : 2000 Standard Classification of Soils for Engineering Purposes (Unified Soil Classification System)
    ASTM D 2487 : 2006 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
    ASTM D 2487 : 2011 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
    AASHTO T 99 : 2015 METHOD OF TEST FOR MOISTURE-DENSITY RELATIONS OF SOILS USING A 2.5-KG (5.5-LB) RAMMER AND A 305-MM (12-IN.) DROP
    SAE J 211/2 : 2014 INSTRUMENTATION FOR IMPACT TEST - PART 2: PHOTOGRAPHIC INSTRUMENTATION
    ASTM D 2487 : 2017 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
    AASHTO MASH 1 : 0 MANUAL FOR ASSESSING SAFETY HARDWARE
    ASTM D 2487 : 1969 : R1975 Standard Test Method for Classification Of Soils For Engineering Purposes
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective