• There are no items in your cart

ASTM F 894 : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Polyethylene (PE) Large Diameter Profile Wall Sewer and Drain Pipe
Available format(s)

Hardcopy , PDF

Superseded date

03-09-2024

Language(s)

English

Published date

03-12-2019

This specification covers requirements and test methods for materials, dimensions, workmanship, ring stiffness, flattening, joint systems, and a form of marking for large diameter, 10 to 132 in. (250 to 3355 mm), inside diameter based polyethylene (PE) pipe of profile wall construction and with bell and spigot, heat fusion, extrusion welded or elctrofusion joints for use in gravity flow applications, such as for sewers and drains.

1.1This specification covers requirements and test methods for materials, dimensions, workmanship, ring stiffness, flattening, joint systems, and a form of marking for large diameter, 10 to 132 in. (250 to 3355 mm), inside diameter based polyethylene (PE) pipe of profile wall construction and with bell and spigot, heat fusion, extrusion welded or elctrofusion joints for use in gravity flow applications, such as for sewers and drains.

Note 1:Pipe produced to this specification should be installed in accordance with Practice D2321 and with the manufacturer's recommendations.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 17
DocumentType
Standard
Pages
11
ProductNote
This standard also refer to ASTM D2321 - 18,ASTM F412 - 19,ASTM F1290 - 19,ASTM F2620 - 19,Fed. Std. No. 123 .
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 1759 : 1997 : R2018 Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
ASTM F 3533/F3533M : 2023 Standard Guide for Inspection and Acceptance of Installed Thermoplastic Storm and Sanitary Sewer Pipe

ASTM D 2837 : 2013 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM F 585 : 2016 : R2021 Standard Guide for Insertion of Flexible Polyethylene Pipe Into Existing Sewers
ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 2321 : 2005 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2321 : 2009 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2321 : 2014 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2122 : 1998 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM F 585 : 2016 Standard Guide for Insertion of Flexible Polyethylene Pipe Into Existing Sewers
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM F 477 : 2014 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 2837 : 2001 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM F 2620 : 2011 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 2620 : 2020 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 3212 : 1996 : REV A : R2003 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM F 477 : 2002 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 3212 : 2007 : R2020 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM D 2412 : 2011 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 3350 : 2000 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2412 : 2002 : R2008 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM F 2620 : 2011 : EDT 1 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 2321 : 2018 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2321 : 2011 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM F 2620 : 2019 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 2620 : 2020 : REV A : EDT 1 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 3350 : 2008 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2837 : 2002 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 2837 : 2001 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM F 1290 : 1998 : REV A : R2004 Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
ASTM D 3350 : 2021 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2837 : 2004 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 2021 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2412 : 2010 : REV A Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 3350 : 2002 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2321 : 2000 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM F 2620 : 2013 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3350 : 2014 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3212 : 2007 : R2013 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 2837 : 2008 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 1998 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 2321 : 2004 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM F 477 : 2014 : R2021 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 2837 : 2001 : REV A : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 2412 : 1996 : REV A Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 3350 : 2004 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2837 : 2011 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 3350 : 2002 : REV A Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3212 : 2007 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM D 3350 : 2012 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3350 : 2001 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2412 : 2002 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 3350 : 2012 : EDT 1 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2122 : 1998 : EDT 1 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2321 : 2014 : EDT 1 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2321 : 1974 Recommended Practice for Underground Installation Of Flexible Thermoplastic Sewer Pipe
ASTM D 2321 : 2004 : EDT 1 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 3212 : 1996 : REV A : R2003 : EDT 1 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM D 2837 : 2022 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM F 2620 : 2012 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM F 2620 : 2006 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 3212 : 2020 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM D 2412 : 2021 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 2122 : 2022 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 3212 : 2021 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM D 3212 : 1996 : REV A Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
ASTM D 3350 : 2010 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM F 1290 : 1998 : REV A : R2011 Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 3350 : 2006 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM F 2620 : 2020 : REV A Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 2321 : 2008 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2122 : 1998 : R2004 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3350 : 2010 : REV A Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM F 1290 : 1998 : REV A Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
ASTM F 2620 : 2020 : REV A : EDT 2 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 2321 : 2020 Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
ASTM D 2412 : 2011 : R2018 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 2122 : 1998 : R2010 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 2412 : 2010 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 3350 : 2005 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM F 2620 : 2009 : EDT 1 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
ASTM D 2122 : 2015 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2837 : 2013 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 2004 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.