BS 2X 34:1998
Current
The latest, up-to-date edition.
Hardcopy , PDF
English
11-16-2005
Committees responsible
Foreword
1 Scope
2 Normative references
3 Definitions
4 Materials
5 Performance
6 Batch inspection
7 Marking
Annex A (normative) Type approval
Annex B (normative) Preparation of test panels
List of references
Describes requirements for the materials and performance of two types of two pack polyurethane finish, for air-drying at ambient temperature, in a range of gloss levels, for aerospace applications.
This British standard specifies requirements for the materials and performance of two types of two pack polyurethane finish, for air-drying at ambient temperature, in a range of gloss levels, for aerospace applications.
Type A materials are intended for interior and exterior use where maximum resistance to fluid attack is required.
Type B materials are intended for exterior surfaces, and offer increased tolerance to flexing compared with type A materials.
The polyurethane finish, as part of a paint scheme including a primer, is intended for application to metallic and non-metallic surfaces to give protection against corrosion and resistance to aircraft fluids and to offer surface appearance in terms of colour and level of gloss as specified by the purchaser.
Information on application for type approval is provided in Annex A.
| Committee |
ACE/65
|
| DevelopmentNote |
Supersedes 96/705060 DC and BS X34(1992) (07/2005) Reviewed and confirmed by BSI, December 2009. (11/2009)
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
| BS X 36:1998 | Specification for paint remover for air drying selectively removable paint scheme for aerospace purposes |
| DEFSTAN 03-4/5(2006) : 2006 | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
| DEFSTAN 80-16/4(2006) : 2006 | PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE TYPE - TYPE 1: HIGH VISCOSITY (BRUSHING) TYPE 2: LOW VISCOSITY (SPRAYING) |
| DEFSTAN 00-970(PT0)/9(2012) : 2012 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/17(2016) : 2016 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/7(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/14(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-80/1(2012) : 2012 | SOLAR HEAT REFLECTANCE REQUIREMENTS OF PAINTS FOR MILITARY EQUIPMENT |
| DEFSTAN 00-970(PT0)/13(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/11(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 05-133(PT1)/1(2011) : 2011 | METHODS FOR TESTING PAINTS, CHEMICALS AND ASSOCIATED PRODUCTS - PART 1: PAINTS AND ALLIED PRODUCTS |
| DEFSTAN 00-970(PT0)/15(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/12(2014) : 2014 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 07-85(PT1)/3(2006) : 2006 | DESIGN REQUIREMENTS FOR WEAPONS AND ASSOCIATED SYSTEMS - PART 1: MANDATORY DESIGN REQUIREMENTS |
| DEFSTAN 03-4/6(2011) : 2011 | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF SPECIFIED MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
| DEFSTAN 00-970(PT0)/8(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 80-14/2(2006) : 2006 | PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE NON AEROSPACE USE TYPE: BRUSHING |
| DEFSTAN 80-221/1(2009) : 2009 | PAINT REMOVER FOR AIR DRYING PAINT SCHEME FOR AEROSPACE PURPOSES - TYPE 1: HIGH VISCOSITY (BRUSHING) - TYPE 2: LOW VISCOSITY (SPRAYING) |
| DEFSTAN 80-212/2(2006) : 2006 | PAINT, FINISHING, POLYURETHANE, ABRASION RESISTING, LOW VOC, MULTI-PACK |
| DEFSTAN 00-970(PT0)/16(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| DEFSTAN 00-970(PT0)/10(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
| BS 2X 33:1998 | Specification for two component epoxy primer for aerospace purposes |
| 14/30290245 DC : 0 | BS 2X35:2003 + A1 - SELECTIVELY REMOVABLE INTERMEDIATE COATING FOR AEROSPACE PURPOSES |
| BS X 35:1998 | Specification for selectively removable intermediate coating for aerospace purposes |
| SAE AMS03-4A : 2015(S2017) | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF SPECIFIED MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
| BS 2X 32:1998 | Specification for pre-treatment etch primer for aerospace purposes |
| BS 2X 35(2003) : 2003 | SELECTIVELY REMOVABLE INTERMEDIATE COATING FOR AEROSPACE PURPOSES |
| BS EN ISO 1514:2004 | Paints and varnishes. Standard panels for testing |
| BS EN ISO 1513:1995 | Paints and varnishes. Examination and preparation of samples for testing |
| BS EN ISO 3696:1995 | Water for analytical laboratory use. Specification and test methods |
| BS EN 23270:1991 | Specification for temperatures and humidities for conditioning and testing paints, varnishes and their raw materials |
| BS EN ISO 6272:1994 | Paints and varnishes. Falling-weight test |
| BS EN ISO 2431:2011 | Paints and varnishes. Determination of flow time by use of flow cups |
| BS 3900-D9:1986 | Methods of test for paints. Optical tests on paint films Determination of colour and colour difference: measurement |
| DEFSTAN 79-17/1(1994) : INTERIM | COMPOUND, CLEANING, FOAMING, FOR AIRCRAFT SURFACES |
| DEFSTAN 79-17/2(1998) : 1998 | COMPOUND, CLEANING, FOAMING, FOR AIRCRAFT SURFACES |
| BS EN ISO 1520:2006 | Paints and varnishes. Cupping test |
| BS EN 29117:1992 | Methods of test for paints. Tests associated with paint film formation Paints and varnishes. Determination of through-dry state and through-dry time. Method of test |
| BS L 163:1978 | Specification for sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated, cold worked for flattening and aged at room temperature) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8) |
| BS 3900-D10:1986 | Methods of test for paints Determination of colour and colour difference: calculation |
| BS 3900-D8:1986 | Methods of test for paints. Optical tests on paint films Determination of colour and colour difference: principles |
| BS EN 2334:1997 | Chromic-sulphuric acid pickle of aluminium and aluminium alloys |
| BS 2X 33:1998 | Specification for two component epoxy primer for aerospace purposes |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.