BS 3692:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
ISO metric precision hexagon bolts, screws and nuts. Specification
Hardcopy , PDF
10-31-2014
English
05-15-2001
Committees responsible
Foreword
1 Scope
2 Normative references
3 Finishes
4 General dimensions
5 Length of bolts and screws
6 Ends of bolts and screws
7 Screw threads
8 Length of thread on bolts and screws
9 Angularity and eccentricity of bolts, screws and nuts
10 Chamfering, washer facing and countersinking
11 Strength grade designation system for steel bolts and screws
12 Material and manufacture of steel bolts and screws
13 Mechanical properties of steel bolts and screws
14 Strength grade designation system for steel nuts
15 Material and manufacture of steel nuts
16 Mechanical properties of steel nuts (excluding thin nuts)
17 Drilled bolts with split pin holes
18 Marking and identification
19 Inspection and testing
20 Complete designation for the purpose of an enquiry or order
Annex A (normative) Recommended gauge for checking
squareness of thread to face of nut
Annex B (normative) Chemical composition of steel nuts
Annex C (normative) testing of mechanical properties of
steel nuts
Annex D (informative) Association of bolt and screw lengths
and diameters
Annex E (informative) Basis for the derivation of tolerances
Annex F (informative) Manufacturer's recommended range of
sizes
Bibliography
Figure 1 to 12
Figure A.1 to E.17
Table 1 to 10
Table B.1 to F.2
Gives the general dimensions and tolerances of precision hexagon bolts, screws and nuts with ISO metric threads in diameters from 1.6 mm to 68 mm inclusive.
| Committee |
FME/9
|
| DevelopmentNote |
Supersedes BS 3692(1967) (03/2001) Supersedes 00/711040 DC. (06/2005) Reviewed and confirmed by BSI, March 2013. (03/2013)
|
| DocumentType |
Standard
|
| Pages |
40
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS 5950-2:1992 | Structural use of steelwork in building Specification for materials, fabrication and erection: hot-rolled sections |
| BS 873-7:1984 | Road traffic signs and internally illuminated bollards Specification for posts and fittings |
| BS 4878:1973 | Specification for large (vee-throated) haulage rope pulleys for mines and quarries |
| ISO 19902:2007 | Petroleum and natural gas industries Fixed steel offshore structures |
| BS 4439:1969 | Specification for screwed studs for general purposes. Metric series |
| BS 1414:1975 | Specification for steel wedge gate valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries |
| DEFSTAN 81-73/3(2007) : 2007 | GUIDE ON USE OF CAPTIVE FASTENERS |
| BS 853-1:1990+A3:2011 | Specification for vessels for use in heating systems Calorifiers and storage vessels for central heating and hot water supply |
| BS 5131-5.9:1979 | Methods of test for footwear and footwear materials. Testing of complete footwear Strength of top piece attachment to shoe heels |
| DEFSTAN 02-862(PT5)/2(2007) : 2007 | FASTENERS - PART 5: NON-FERROUS (SUBMARINE FIRST LEVEL QUALITY ASSURED) |
| BS 7019:1989 | Specification for fully screened 400 A bolted flameproof cable couplers and adaptors for use on systems up to and including 6.6 kV, primarily for use in mines |
| BS 466:1984 | Specification for power driven overhead travelling cranes, semi-goliath and goliath cranes for general use |
| BS 227:1995 | Specification for H-section steel arches for use in mines |
| DEFSTAN 02-862(PT1)/2(2007) : 2007 | FASTENERS - PART 1: GENERAL |
| BS 5160:1989 | Specification for steel globe valves, globe stop and check valves and lift type check valves |
| BS EN 1515-4:2009 | Flanges and their joints. Bolting Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| BS 1722-12:1999 | Fences Specification for steel palisade fences |
| BS 5041-2:1987 | Fire hydrant systems equipment Specification for landing valves for dry risers |
| BS 1873:1975 | Specification for steel globe and globe stop and check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries |
| EN ISO 19902:2007/A1:2013 | PETROLEUM AND NATURAL GAS INDUSTRIES - FIXED STEEL OFFSHORE STRUCTURES (ISO 19902:2007/AMD 1:2013) |
| BS 1892-2.9:1986 | Gymnasium equipment. Particular requirements Specification for weight training equipment |
| BS PD5500(2018) : 2018 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 5386-3:1980 | Specification for gas burning appliances Domestic cooking appliances burning gas |
| BS 6946:1988 | Specification for metal channel cable support systems for electrical installations |
| I.S. EN 1515-4:2009 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| UNE-EN 1515-4:2010 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| BS 2573-2:1980 | Rules for the design of cranes Specification for classification, stress calculations and design of mechanisms |
| BS 4772:1988 | Specification for ductile iron pipes and fittings |
| BS PD5500(2012) : 2012 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| PD 5500:2003 | Specification for unfired fusion welded pressure vessels |
| BS 5306-2:1990 | Fire extinguishing installations and equipment on premises Specification for sprinkler systems |
| BS 7608(2014) : 2014 | GUIDE TO FATIGUE DESIGN AND ASSESSMENT OF STEEL PRODUCTS |
| DEFSTAN 02-862(PT1)/3(2011) : 2011 | NAVAL FASTENERS - PART 1: MATERIAL SELECTION AND USE |
| BS 4882:1990 | Specification for bolting for flanges and pressure containing purposes |
| BS 5041-1:1987 | Fire hydrant systems equipment Specification for landing valves for wet risers |
| DEFSTAN 02-862(PT3)/3(2011) : 2011 | NAVAL FASTENERS - PART 3: PROCUREMENT OF FIRST LEVEL FASTENERS |
| BS 8006-1(2010) : 2010 | CODE OF PRACTICE FOR STRENGTHENED/REINFORCED SOILS AND OTHER FILLS |
| DEFSTAN 02-728/2(2001) : INTERIM | REQUIREMENTS FOR DOMESTIC HOT AND COLD FRESH WATER SYSTEMS |
| BS 5400-3:2000 | Steel, concrete and composite bridges Code of practice for design of steel bridges |
| DEFSTAN 81-86/3(2007) : 2007 | METAL FITTINGS FOR WOODEN CONTAINERS |
| BS 5159:1974 | Specification for cast iron and carbon steel ball valves for general purposes |
| DEFSTAN 02-862(PT4)/2(2007) : 2007 | FASTENERS - PART 4: FERROUS (SUBMARINE FIRST LEVEL QUALITY ASSURED) |
| DEFSTAN 02-862(PT2)/3(2011) : 2011 | NAVAL FASTENERS - PART 2: PROCUREMENT OF NON-FIRST LEVEL FASTENERS |
| BS 449-2:1969 | Specification for the use of structural steel in building Metric units |
| DEFSTAN 02-862(PT2)/2(2007) : 2007 | FASTENERS - PART 2: FERROUS |
| BS 5292:1980 | Specification for jointing materials and compounds for installations using water, low-pressure steam or 1st, 2nd and 3rd family gases |
| BS 5154:1991 | Specification for copper alloy globe, globe stop and check, check and gate valves |
| EN 1515-4:2009 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| BS 4790:1987 | Method for determination of the effects of a small source of ignition on textile floor coverings (hot metal nut method) |
| BS PD5500(2009) : 2009 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 5078:1974 | Specification for jig and fixture components |
| DEFSTAN 05-34/2(1984) : 1984 | MARKING OF SERVICE MATERIAL |
| DEFSTAN 02-728/3(2010) : 2010 | REQUIREMENTS FOR DOMESTIC HOT AND COLD FRESH WATER SYSTEMS |
| BS EN ISO 19902 : 2007 | PETROLEUM AND NATURAL GAS INDUSTRIES - FIXED STEEL OFFSHORE STRUCTURES |
| DEFSTAN 81-86/2(2000) : 2000 CORR 2000 | METAL FITTINGS FOR WOODEN CONTAINERS |
| BS 5158:1989 | Specification for cast iron plug valves |
| BS 5067:1985 | Specification for flameproof transformers for use in mines |
| BS 856:1969 | Specification for wing nuts |
| BS 4190:2001 | ISO metric black hexagon bolts, screws and nuts. Specification |
| BS 1916-2:1953 | Limits and fits for engineering Guide to the selection of fits in BS 1916:Part 1 |
| BS EN ISO 1234:1998 | Split pins |
| BS EN ISO 6506-1:2014 | Metallic materials. Brinell hardness test Test method |
| BS EN ISO 6507-3:2005 | Metallic materials. Vickers hardness test Calibration of reference blocks |
| BS 3643-1:1981 | ISO metric screw threads Principles and basic data |
| BS EN ISO 6507-1:2005 | Metallic materials. Vickers hardness test Test method |
| BS EN ISO 6506-2:2014 | Metallic materials. Brinell hardness test Verification and calibration of testing machines |
| BS 3580:1964 | Guide to design considerations on the strength of screw threads |
| BS EN 10109-2:1996 | Metallic materials. Hardness test Verification of Rockwell hardness testing machines (scales A, B, C, D, E, F, G, H, K, N, T) |
| BS EN 20286-1:1993 | ISO system of limits and fits ISO system of limits and fits. Bases of tolerances, deviations and fits |
| BS EN 20898-2:1994 | Mechanical properties of fasteners Nuts with specified proof load values. Coarse thread |
| BS EN 10109-3:1996 | Metallic materials. Hardness test Calibration of standardized blocks to be used for Rockwell hardness testing machines (scales A, B, C, D, E, F, G, H, K, N, T) |
| BS EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread |
| BS EN ISO 6506-3:2014 | Metallic materials. Brinell hardness test Calibration of reference blocks |
| BS EN ISO 6507-2:2005 | Metallic materials. Vickers hardness test Verification and calibration of testing machines |
| BS EN ISO 4759-1:2001 | Tolerances for fasteners Bolts, screws, studs and nuts. Product grades A, B and C |
| BS EN 20286-2:1993 | ISO system of limits and fits ISO system of limits and fits. Tables of standard tolerance grades and limit deviations for holes and shafts |
| BS EN 10045-1:1990 | Charpy impact test on metallic materials Test method (V- and U-notches) |
| BS EN 10109-1:1996 | Metallic materials. Hardness test Rockwell test (scales A, B, C, D, E, F, G, H, K) and Rockwell superficial test (scales 15 N, 30 N, 45 N, 15 T, 30 T and 45 T) |
| BS 1916-3:1963 | Limits and fits for engineering Recommendations for tolerances, limits and fits for large diameters |
| BS EN ISO 4042:2000 | Fasteners. Electroplated coatings |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.