• There are no items in your cart

BS 4500-1.1(1990) : AMD 7630

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

ISO LIMITS AND FITS - GENERAL, TOLERANCES AND DEVIATIONS - SPECIFICATION FOR BASES OF TOLERANCES, DEVIATIONS AND FITS
Superseded date

08-15-1993

Published date

11-23-2012

National foreword
Committees responsible
Specification
0. Introduction
1. Scope
2. Field of application
3. References
4. Terms and definitions
5. Symbols, designation and interpretation of
     tolerances, deviations and fits
6. Graphical representation
7. Reference temperature
8. Standard tolerances for basic sizes up to 3 150 mm
10. Bibliography
Annexes
A. Bases of the ISO system of limits and fits
B. Examples of the use of ISO 286-1
C. Equivalent terms
Tables
1. Numerical values of standard tolerance grades IT
     for basic sizes up to 3 150 mm
2. Numerical values of the fundamental deviations of
     shafts
3. Numerical values of the fundamental deviations of
     holes
4. Basic size steps
5. Numerical values for standard tolerances in grades
     IT01 and IT0
6. Formulae for standard tolerances in grades IT01,
     IT0 and IT1 for basic sizes up to and including
     500 mm
7. Formulae for standard tolerances in grades IT1 to
     IT18
8. Rounding for IT values up to and including standard
     tolerance grade IT11
9. Formulae for fundamental deviations for shafts and
     holes
10. Rounding for fundamental deviations
Figures
1. Basic size, and maximum and minimum limits of size
2. Conventional representation of a tolerance zone
3. Clearance
4. Clearance fit
5. Transition fit
6. Interference
7. Interference fit
8. Schematic representation of clearance fits
9. Schematic representation of interference fits
10. Schematic representation of transition fits
11. Shaft-basis system of fits
12. Hole-basis system of fits
13. Schematic representation of the positions of
     fundamental deviations
14. Deviations for shafts and holes
15. Graphical representation
16. Simplified schematic diagram
17. Deviations for shafts
18. Deviations for holes
19. Deviations js and JS
20. Diagrammatic representation of the rule given in
     A.4.2 b)

Establishes the bases of ISO system of limits and fits together with the calculated values of the standard tolerances and fundamental deviations. These values shall be taken as authoritative. Also gives terms and definitions together with associated symbols. Contains several tables and figures. BS AMD 7630 RENUMBERS THIS STANDARD TO BS EN 20286 PT1

Committee
GME/5
DevelopmentNote
Superseded and renumbered by BS EN 20286-1 (09/1996)
DocumentType
Standard
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 286-1:2010 Identical

BS EN 10045-1:1990 Charpy impact test on metallic materials Test method (V- and U-notches)
BS 341-1:1991 Transportable gas container valves Specification for industrial valves for working pressures up to and including 300 bar
BS 7724:1994 Specification for split pins (metric series)
BS 7679:1993 Plain bearings. Quality control techniques and inspection of geometrical and material quality characteristics
BS 328-1:1993 Drills and reamers Specification for twist drills
BS 4480-1:1992 Plain bearings: metric series Sintered bushes. Dimensions and tolerances
BS 5621:1992 Specification for dimensions of rotary masonry and rotary masonry impact drills with hardmetal tips
BS 7296-1:1990 Cavities for hydraulic fluid power cartridge valves Specification for two-port slip-in valves
BS QC 030000:1993 Harmonized system of quality assessment for electronic components. Rectangular connectors for frequencies below 3 MHz. Generic specification. General requirements and guide for the preparation of detail specifications for connectors with assessed quality
BS 1574:1994 Specification for split pins (inch series)
BS 7637:1993 Specification for linear motion, recirculating ball, sleeve type rolling bearings (metric series)
BS QC 960000:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Generic specification
BS 5341-6.1:1992 Piston rings up to 200 mm diameter for reciprocating internal combustion engines. Vocabulary, inspection methods and generic specifications Vocabulary

ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
ISO 5166:1982 System of cone fits for cones from C = 1 : 3 to 1 : 500, lengths from 6 to 630 mm and diameters up to 500 mm
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 1:2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties
ISO 406:1987 Technical drawings Tolerancing of linear and angular dimensions
ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO/R 1938:1971 ISO system of limits and fits Part II : Inspection of plain workpieces

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.