Skip to content
Please enter a keyword to search

  • BS 7117-1:1991

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    METERING PUMPS AND DISPENSERS TO BE INSTALLED AT FILLING STATIONS AND USED TO DISPENSE LIQUID FUEL - PART 1: SPECIFICATION FOR CONSTRUCTION

    Available format(s):  Hardcopy, PDF

    Superseded date:  10-21-2004

    Language(s):  English

    Published date:  01-01-1991

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Committees responsible
    Foreword
    Introduction
    1 Scope
    2 Definitions
    3 Classification of fuels
    4 Classification of hazardous areas
    5 Classification of mode of operation of dispensing
        equipment
    6 Classification of pump facilities
    7 Classification of vapour barriers
    8 Construction and performance
    9 Marking and labelling
    10 Manufacturer's instructions
    Appendix
    A Bibliography
    Figures
    Publication(s) referred to

    Abstract - (Show below) - (Hide below)

    Establishes requirements for metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats, light aircraft and portable containers. Gives particular attention to electrical, mechanical and hydraulic equipment and electrical apparatus installed within, or mounted on, the housings of metering pumps or dispensers. Does not include any requirements for metering performance such as those specified under the Weights and Measures Legislation. Applicable to equipment for fuels which are flammable liquids having a flash point not exceeding 100 degrees C.

    General Product Information - (Show below) - (Hide below)

    Committee PCL/6
    Development Note Supersedes 02/705248 DC, 90/30640 DC, 96/208377 DC and BS 7117-1(1989) (01/2003)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    BS 3955:1986 SPECIFICATION FOR ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR GENERAL PURPOSES
    BS 3395:1989 SPECIFICATION FOR ELECTRICALLY BONDED RUBBER HOSES AND HOSE ASSEMBLIES FOR DISPENSING PETROLEUM BASED FUELS
    BS 5501-9:1982 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - SPECIFICATION FOR INTRINSICALLY SAFE ELECTRICAL SYSTEMS 'I'
    BS 5501-4:1977 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - POWDER FILLING 'Q'
    BS 7117-3:1991 METERING PUMPS AND DISPENSERS TO BE INSTALLED AT FILLING STATIONS AND USED TO DISPENSE LIQUID FUEL - GUIDE TO MAINTENANCE AFTER INSTALLATION
    BS 5501-7:1977 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INTRINSIC SAFETY 'I'
    BS 5419:1977 SPECIFICATION FOR AIR BREAK SWITCHES AIR BREAK DISCONNECTORS AIR BREAK SWITCH DISCONNECTORS AND FUSE COMBINATION UNITS FOR VOLTAGES UP TO AND INCLUDING 1000 V A.C. AND 1200 V D.C.
    BS 7671(2001) : 2001 AMD 14905 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS
    BS 5501-6:1977 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INCREASED SAFETY 'E'
    BS 5501-1:1977 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - GENERAL REQUIREMENTS
    BS 5501-5:1977 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - FLAMEPROOF ENCLOSURE 'D'
    BS 889:1965 SPECIFICATION FOR FLAMEPROOF ELECTRIC LIGHTING FITTINGS
    BS 4683-1:1971 Specification for electrical apparatus for explosive atmospheres Classification of maximum surface temperatures
    BS EN 13012:2012 PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS
    BS 5501-8:1988 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - ENCAPSULATION 'M'
    BS 5501-2:1977 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - OIL IMMERSION 'O'
    BS 6941:1988 SPECIFICATION FOR ELECTRICAL APPARATUS FOR EXPLOSIVE ATMOSPHERES WITH TYPE OF PROTECTION N
    BS 5501-3:1977 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PRESSURIZED APPARATUS 'P'
    BS 7117-2:1991 METERING PUMPS AND DISPENSERS TO BE INSTALLED AT FILLING STATIONS AND USED TO DISPENSE LIQUID FUEL - GUIDE TO INSTALLATION
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective