• There are no items in your cart

BS 7613:1994

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Specification for hot rolled quenched and tempered weldable structural steel plates
Available format(s)

Hardcopy , PDF

Superseded date

04-15-1996

Language(s)

English

Published date

06-15-1994

Committees responsible
Foreword
Specification
1 Scope
2 References
3 Definitions
4 General
5 Information to be supplied by the purchaser
6 Steelmaking process
7 Supply condition
8 Chemical composition
9 Weldability
10 Quality of finished steel
11 Identification of cast
12 Marking
13 Test certificates
14 Mass of steel
15 Tolerances
16 Selection and identification of test samples
17 Number of tensile tests
18 Direction and position of tensile test samples
19 Tensile test pieces
20 Tensile test
21 Number of impact tests
22 Position of impact test samples
23 Impact test pieces
24 Impact tests
25 Bend tests
26 Retests
Annexes
A (informative) Comparison between designations in
    this standard and the BS 4360 : 1990
B (normative) Options
C (normative) Positions of test samples for tensile
    test
D (normative) Position of test piece to be taken from
    tensile test samples when two rolled surfaces
    cannot be retained
E (normative) Position of test samples for impact
    tests
F (informative) Indicative Charpy V-notch impact
    values at temperatures other than those given in
    table 3
G (normative) Bend test for thicknesses up to and
    including 25 mm
Tables
1 Permitted deviations in product analysis from
    specified ladle analysis percentages
2 Chemical composition (ladle analysis)
3 Mechanical properties
4 Maximum CEV
5 Indicative Charpy V-notch impact values
6 Bend test requirements for thicknesses up to and
    including 25 mm
7 Recommended minimum internal forming diameters for
    guidance only
Figures
1 Location of impact test pieces
2 Positions of test samples for tensile test
3 Position of test piece to be taken from tensile test
    samples when two rolled surfaces cannot be retained
4 Position of test samples for impact tests
List of references

Specifies requirements for weldable steels for general structural and engineering purposes in the form of hot rolled quenched and tempered plates. Coverage includes definitions, steelmaking process, chemical composition, weldability, marking, tolerances, and number of tensile tests. Also gives detailed tables, diagrams and annexes.

Committee
ISE/103
DevelopmentNote
Together with BS 7668(1994), BS EN 10029, BS EN 10113-1, BS EN 10113-2, BS EN 10113-3, BS EN 10155 and BS EN 10210-1 supersedes BS 4360(1990). (07/2005)
DocumentType
Standard
Pages
16
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EURONORM 137 PT1 : 1983 Similar to

EN 10113-2 : 1993 HOT-ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED STEELS
EN 10113-3 : 1993 HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED STEELS
BS 6349-1:2000 Maritime structures Code of practice for general criteria
BS EN 10113-2:1993 Hot-rolled products in weldable fine grain structural steels Delivery conditions for normalized/normalized rolled steels
EEMUA 159 : 2014 ABOVE GROUND FLAT BOTTOMED STORAGE TANKS - A GUIDE TO INSPECTION, MAINTENANCE AND REPAIR
BS EN 10113-3:1993 Hot-rolled products in weldable fine grain structural steels Delivery conditions for thermomechanical rolled steels
BS 5975:1996 Code of practice for falsework

BS EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product. Technical delivery conditions
BS 3894-1:1965 Method for converting elongation values for steel Carbon and low alloy steels
BS 6562-2:1986 Terms used in the iron and steel industry Glossary of terms used in classifying and defining steel industry products by shape and dimensions
BS 1837:1970 Methods for the sampling of iron, steel, permanent magnet alloys and ferro-alloys
BS EN 10029:2010 Hot-rolled steel plates 3 mm thick or above. Tolerances on dimensions and shape
BS 5996:1980 Methods for ultrasonic testing and specifying quality grades of ferritic steel plate
BS EN 10045-1:1990 Charpy impact test on metallic materials Test method (V- and U-notches)
BS EN 10002-1:2001 Tensile testing of metallic materials Method of test at ambient temperature
BS EN 10163-2:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Plate and wide flats

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.