• There are no items in your cart

BS EN 12007-2:2012

Current
Current

The latest, up-to-date edition.

Gas infrastructure. Pipelines for maximum operating pressure up to and including 16 bar Specific functional requirements for polyethylene (MOP up to and including 10 bar)
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

08-31-2012

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Design
5 Construction
6 Quality control
7 Pressure testing
Annex A (informative) - Storage, handling
        and transportation
Annex B (informative) - Fusion joint integrity
Annex C (informative) - Technical changes between
        this European Standard and EN 12007-2:2000
Bibliography

Specifies the specific functional requirements for polyethylene (PE) pipelines in addition to the general functional requirements of EN 12007-1 for: a) a maximum operating pressure (MOP) up to and including 10 bar; b) an operating temperature between -20 degrees C and +40 degrees C.

This European Standard describes the specific functional requirements for polyethylene (PE) pipelines in addition to the general functional requirements of EN 12007-1 for: a maximum operating pressure (MOP) up to and including 10 bar; an operating temperature between -20 °C and +40 °C. This European Standard covers three types of pipe: PE pipes including any identification stripes; PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe; PE pipes with a peelable, contiguous thermoplastics additional layer on the outside of the pipe. This European Standard specifies common basic principles for gas infrastructure. Users of this European Standard should be aware that more detailed national standards and/or code of practice may exist in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles. In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this European Standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts). CEN/TR 13737 (all parts) give: clarification of all legislations/regulations applicable in a member state; if appropriate, more restrictive national requirements; a national contact point for the latest information.

Committee
GSE/33
DevelopmentNote
Supersedes 95/709431 DC (08/2004) Supersedes 10/30208795 DC. (08/2012)
DocumentType
Standard
Pages
32
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
DIN EN 12007-2:2012-10 Identical
UNE-EN 12007-2:2013 Identical
SN EN 12007-2:2012 Identical
NF EN 12007-2 : 2012 Identical
NBN EN 12007-2 : 2012 Identical
UNI EN 12007-2 : 2012 Identical
I.S. EN 12007-2:2012 Identical
NS EN 12007-2 : 2012 Identical
NEN EN 12007-2 : 2012 Identical
EN 12007-2:2012 Identical

EN 12327:2012 Gas infrastructure - Pressure testing, commissioning and decommissioning procedures - Functional requirements
EN 1555-1:2010 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
EN 1555-3:2010+A1:2012 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
EN 12007-3:2015 Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 3: Specific functional requirements for steel
EN 12007-1:2012 Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements
ISO 10838-2:2000 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
ISO 21307:2011 Plastics pipes and fittings Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems
ISO 10838-1:2000 Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
ISO 12176-1:2017 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
ISO 3:1973 Preferred numbers Series of preferred numbers
ISO 12176-2:2008 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion
ISO 11414:2009 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
EN 1555-4:2011 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves
EN 1555-5:2010 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 1555-2:2010 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
EN 12007-4:2012 Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation
ISO 11413:2008 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.