• There are no items in your cart

BS EN 1337-5:2005

Current
Current

The latest, up-to-date edition.

Structural bearings Pot bearings
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

12-29-2006

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Functional requirements
5 Materials
6 Design requirements
7 Manufacturing assembly and tolerances
8 Conformity evaluation
9 Installation
10 In-service inspection
Annex A (normative) Internal seals
Annex B (informative) Determination of compression stiffness
Annex C (informative) Factory Production Control (FPC)
Annex D (normative) Determination of restraint moment
Annex E (normative) Long term rotation and load test
Annex F (normative) Test equipment
Annex G (informative) Application of internal seals
Annex ZA (informative) Clauses of this European Standard
         addressing the provisions of the EU Construction
         Products Directive
Bibliography

Describes the requirements for the design and manufacture of pot bearings which will be used for operating temperatures between -40 degrees C and 50 degrees C.

This part of EN 1337 specifies the requirements for the design and manufacture of pot bearings which will be used for operating temperatures between - 40 °C and 50 °C. This part of EN 1337 does not apply to pot bearings made with other materials than those specified in clause 5. Bearings which are subjected to rotation ad greater than 0,030 rad (see Figure 2) under the characteristic combination of actions or which incorporate elastomeric pads larger than 1500 mm in diameter are beyond the scope of this document. Depending on the climatic region where the construction work is located the bearings can be designed to one of the following classes related to minimum operating temperatures (the minimum shade air temperatures): - 25 °C or - 40 °C. When required to accommodate translational movements, pot bearings may be combined with sliding elements in accordance with EN 1337-2. NOTE The minimum shade air temperature for a location should be obtained from meteorological data appropriate to a 120 year return period. Consideration should be given to adjustment of this temperature for height and local divergence such as frost pockets and sheltered low-lying areas if the data obtained applies to a general area rather than to a specific location.

Committee
B/522
DevelopmentNote
Supersedes 96/106185 DC. (12/2006) Together with BS EN 1337-1, BS EN 1337-2, BS EN 1337-3, BS EN 1337-4, BS EN 1337-6, BS EN 1337-7, BS EN 1337-8, BS EN 1337-9, BS EN 1337-10 and BS EN 1337-11, supersedes BS 5400-9.1(1983) and BS 5400-9.2(1983). (10/2009)
DocumentType
Standard
Pages
60
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
I.S. EN 1337-5:2005 Identical
DIN EN 1337-5:2005-07 Identical
NBN EN 1337-5 : 2005 Identical
UNE-EN 1337-5:2006 Identical
NS EN 1337-5 : 1ED 2006 Identical
NF EN 1337-5 : 2005 Identical
EN 1337-5:2005 Identical
UNI EN 1337-5 : 2005 Identical
NEN EN 1337-5 : 2005 Identical
SN EN 1337-5 : 2005 Identical
DIN EN 1337-5 E : 2005 Identical

PD 6703:2009 Structural bearings. Guidance on the use of structural bearings
BS EN 1991-1-5 NA : 2003 UK NATIONAL ANNEX TO EUROCODE 1: ACTIONS ON STRUCTURES - PART 1-5: GENERAL ACTIONS - THERMAL ACTIONS

93/68/EEC : 1993 AMD 2 1998 COUNCIL DIRECTIVE 93/68/EEC OF 22.7.93 AMENDING DIRECTIVES 87/404/EEC, 88/378/EEC, 89/106/EEC, 89/336/EEC, 89/392/EEC, 89/686/EEC, 90/384/EEC, 90/385/EEC, 90/396/EEC, 91/263/EEC, 92/42/EEC AND 73/23/EEC
EN 1337-1:2000 Structural bearings - Part 1: General design rules
EN ISO 4288 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - RULES AND PROCEDURES FOR THE ASSESSMENT OF SURFACE TEXTURE
ISO 1083:2004 Spheroidal graphite cast irons - Classification
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
ISO 2039-1:2001 Plastics Determination of hardness Part 1: Ball indentation method
EN 1337-2:2004 Structural bearings - Part 2: Sliding elements
EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10088-2:2014 STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
EN 1337-11:1997 Structural bearings - Part 11: Transport, storage and installation
ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
EN 10113-1 : 1993 HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - GENERAL DELIVERY CONDITIONS
EN 1337-9:1997 Structural bearings - Part 9: Protection
EN ISO 2039-1 : 2003 PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD (ISO 2039-1:2001)
EN 10204:2004 Metallic products - Types of inspection documents
EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
EN 1337-10:2003 Structural Bearings - Part 10: Inspection and maintenance
ISO 6446:1994 Rubber products — Bridge bearings — Specification for rubber materials
ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system
EN ISO 1133:2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
EN 1990:2002/A1:2005/AC:2010 EUROCODE - BASIS OF STRUCTURAL DESIGN
ISO 3755:1991 Cast carbon steels for general engineering purposes
ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
EN 10083-3:2006/AC:2008 STEELS FOR QUENCHING AND TEMPERING - PART 3: TECHNICAL DELIVERY CONDITIONS FOR ALLOY STEELS
EN 12163:2016 Copper and copper alloys - Rod for general purposes
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles

View more information
US$330.61
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.