• There are no items in your cart

BS EN 14636-2:2009

Current

Current

The latest, up-to-date edition.

Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC) Manholes and inspection chambers

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-31-2010

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 General requirements
5 Manholes and inspection chamber units
6 Dangerous substances
7 Manufacturer's installation recommendations
8 Evaluation of conformity
Annex A (normative) - Determination of a chamber ring's
        or shaft ring's crushing strength and ring bending
        tensile strength using a ring test piece
Annex B (normative) - Test method for the determination of
        a chamber ring's or shaft ring's crushing strength
        or the ring bending tensile strength using test
        pieces sawn from a ring
Annex C (normative) - Test method for the determination of
        the vertical crushing strength of slabs or tapers
Annex D (normative) - Test method for the determination of
        the compressive strength of polyester resin concrete
        (PRC) using test pieces which are cut from a unit
Annex E (normative) - Test method for the determination of
        the resistance of installed steps to vertical and
        horizontal loading
Annex F (normative) - Method for the assessment of the
        leak-tightness of a manhole or inspection chamber
        and its joints under short term exposure to internal
        water pressure and negative pressure
Annex G (normative) - Test method for the determination of the
        long-term crushing strength (50 years evaluation point)
        of a chamber ring or a shaft ring, including the effects
        of media attack
Bibliography

Describes units made from polyester resin concrete, and their joints, for the construction of inspection chambers with inverts not exceeding 2 m deep and for manholes, intended to be used within a drain or sewer system operating without pressure.

This European Standard specifies units made from polyester resin concrete (PRC, see 3.1.18), and their joints, for the construction of inspection chambers with inverts not exceeding 2 m deep and for manholes, intended to be used within a drain or sewer system operating without pressure. It applies to products for use outside buildings in buried installations to be installed by open-trench techniques.

This document applies to nominal sizes from DN 600 to DN 3000 for chamber rings and shaft rings having a circular shape.

The intended use of these products is to provide access to buried drain or sewer systems for the conveyance of wastewater, i.e. sewage and surface water, at temperatures up to 50 °C, without pressure or occasionally at a head of pressure up to 0,5 bar1), and installed in areas subjected to vehicle and/or pedestrian traffic and outside buildings.

NOTE 1 The attention of readers is drawn to applicable requirements contained in EN 476.

This standard specifies definitions, requirements and characteristics of units and their joints for the construction of manholes and inspection chambers, of materials, test methods, marking and evaluation of conformity.

The units are classified on the basis of its type and the type of structure they are intended to be used.

NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Committee
PRI/88/2
DevelopmentNote
Supersedes 09/30203307 DC. (01/2010)
DocumentType
Standard
Pages
64
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
EN 14636-2:2009 Identical

EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
EN 13121-1:2003 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS
EN 14636-1:2009 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
EN 637:1994/AC:1995 PLASTICS PIPING SYSTEMS - GLASS REINFORCED PLASTICS COMPONENTS - DETERMINATION OF THE AMOUNTS OF CONSTITUENTS USING THE GRAVIMETRIC METHOD
EN 476:2011 General requirements for components used in drains and sewers
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 13101:2002 Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity
ISO 9001:2015 Quality management systems — Requirements
EN 705:1994/AC:1995 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPES AND FITTINGS - METHODS FOR REGRESSION ANALYSES AND THEIR USE

View more information
US$311.44
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.