• There are no items in your cart

BS EN 15657-1:2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Acoustic properties of building elements and of buildings. Laboratory measurement of airborne and structure borne sound from building equipment Simplified cases where the equipment mobilities are much higher than the receiver mobilities, taking whirlpool baths as an example
Available format(s)

Hardcopy , PDF

Superseded date

09-30-2017

Language(s)

English

Published date

11-30-2009

Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Principle of the test method
6 Measuring equipment
7 Test facilities
8 Mounting of the specimen
9 Test procedure and evaluation
10 Calculation of single number descriptors
11 Precision
12 Expression of results
13 Test report
Annex A (normative) - List of symbols
Annex B (informative) - Link to EN 12354-5
Annex C (normative) - Calculation of the reference
                      structure borne sound pressure level
Annex D (informative) - Example of an existing test rig
Annex E (informative) - Measurement procedure for the tub
                        filling phase, using a reference
                        water jet
Bibliography

Specifies the expression of the results, including data for comparison between products (single value descriptors) and input data for the prediction method.

Part 1 of the standard shall apply to any source -receiver configuration where the receiver mobility is 10 dB below the source mobility (see definition of mobility in Clause 3 below). However, part 1 is restricted for the moment to whirlpool baths since only this type of building equipment has been experimentally studied so far; for other types of building equipment, the principle of the method is still valid, but some details in the standard might not be relevant. Therefore, this first part: - specifies methods for the measurement under laboratory conditions of airborne and structure borne sound produced by whirlpool baths connected to low mobility structures; for the case of whirlpool baths, building structures of mass per unit area equal or greater than 220 kg/m2, hollow elements excluded, are considered as low mobility elements; - defines the expression of the results, including data for comparison between products (single value descriptors) and input data for the prediction method (link to standard prEN 12354-5 explained in Annex B).

Committee
EH/1/6
DocumentType
Standard
Pages
28
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

Standards Relationship
EN 15657-1:2009 Identical

ISO 3822-1:1999 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
ISO 10848-1:2017 Acoustics — Laboratory and field measurement of flanking transmission for airborne, impact and building service equipment sound between adjoining rooms — Part 1: Frame document
ISO 16063-21:2003 Methods for the calibration of vibration and shock transducers Part 21: Vibration calibration by comparison to a reference transducer
ISO 7626-1:2011 Mechanical vibration and shock — Experimental determination of mechanical mobility — Part 1: Basic terms and definitions, and transducer specifications
EN ISO 3741:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for reverberation test rooms (ISO 3741:2010)
ISO 140-3:1995 Acoustics — Measurement of sound insulation in buildings and of building elements — Part 3: Laboratory measurements of airborne sound insulation of building elements
ISO 7626-2:2015 Mechanical vibration and shock Experimental determination of mechanical mobility Part 2: Measurements using single-point translation excitation with an attached vibration exciter
EN 12354-5:2009/AC:2010 BUILDING ACOUSTICS - ESTIMATION OF ACOUSTIC PERFORMANCE OF BUILDING FROM THE PERFORMANCE OF ELEMENTS - PART 5: SOUNDS LEVELS DUE TO THE SERVICE EQUIPMENT
ISO 140-1:1997 Acoustics Measurement of sound insulation in buildings and of building elements Part 1: Requirements for laboratory test facilities with suppressed flanking transmission
EN ISO 10848-1:2017 Acoustics - Laboratory and field measurement of flanking transmission for airborne, impact and building service equipment sound between adjoining rooms - Part 1: Frame document (ISO 10848-1:2017)
EN ISO 140-3:1995/A1:2004 ACOUSTICS - MEASUREMENT OF SOUND INSULATION IN BUILDINGS AND OF BUILDING ELEMENTS - PART 3: LABORATORY MEASUREMENTS OF AIRBORNE SOUND INSULATION OF BUILDING ELEMENTS
EN ISO 140-1:1997/A1:2004 ACOUSTICS - MEASUREMENT OF SOUND INSULATION IN BUILDINGS AND OF BUILDING ELEMENTS - PART 1: REQUIREMENTS FOR LABORATORY TEST FACILITIES WITH SUPPRESSED FLANKING TRANSMISSION
EN ISO 3822-1:1999/A1:2008 ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT
ISO 5348:1998 Mechanical vibration and shock Mechanical mounting of accelerometers
ISO 3741:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for reverberation test rooms
EN 60651:1994/A2:2001 SOUND LEVEL METERS (IEC 60651:1979/A2:2000)
IEC 60651:1979+AMD1:1993+AMD2:2000 CSV Sound level meters

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.