• BS EN 1852-1:2018

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene (PP) Specifications for pipes, fittings and the system

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-31-2018

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    European foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviations
    5 Material
    6 General characteristics
    7 Geometrical characteristics
    8 Mechanical characteristics
    9 Physical characteristics
    10 Performance requirements
    11 Sealing rings
    12 Marking
    Annex A (normative) - Utilization of non-virgin
            PP material
    Annex B (informative) - General characteristics
            of PP pipes and fittings
    Annex C (informative) - Product standards of
            components that can be connected to
            components conforming to this standard
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the requirements for solid wall pipes, fittings and the system of polypropylene (PP) piping systems intended for use for: - non-pressure underground drainage and sewerage outside the building structure (application area code 'U'), and - non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code 'D') and outside the building structure.

    Scope - (Show below) - (Hide below)

    This part of EN 1852 specifies the requirements for solid wall pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system of polypropylene (PP) piping systems intended for use for: - non-pressure underground drainage and sewerage outside the building structure (application area code \'U\'), and - non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code \'D\') and outside the building structure. This is reflected in the marking of products by \'U\' and \'UD\'. This standard covers PP materials without mineral modifiers. It also specifies the test parameters for the test methods referred to in this standard. NOTE 1 Solid wall multilayer pipes with different formulation throughout the wall and foamed core pipes are covered by EN 13476-2 [1] (see also CEN ISO/TR 27165 [2]). This standard covers a range of nominal sizes, and pipe series and gives recommendations concerning colours. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with CEN/TS 1852-2, it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 3 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be connected to pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 14.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/88/1
    Development Note Supersedes 00/122013 DC and 95/121337 DC. (08/2003) Supersedes 07/30165577 DC. (04/2009) Supersedes 16/30336859 DC. (02/2018)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 295-3:2012 Vitrified clay pipe systems for drains and sewers - Part 3: Test methods
    ISO 580:2005 Plastics piping and ducting systems Injection-moulded thermoplastics fittings Methods for visually assessing the effects of heating
    EN ISO 3126 : 2005 PLASTICS PIPING SYSTEMS - PLASTICS COMPONENTS - DETERMINATION OF DIMENSIONS
    ISO/TR 10358:1993 Plastics pipes and fittings Combined chemical-resistance classification table
    ISO 3451-1:2008 Plastics Determination of ash Part 1: General methods
    EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
    ISO 13263:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for impact strength
    EN ISO 1043-1:2011/A1:2016 PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMER AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011/AMD 1:2016)
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces
    ISO 265-1:1988 Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
    ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
    ISO 11173:1994 Thermoplastics pipes — Determination of resistance to external blows — Staircase method
    EN ISO 11173 : 2017 THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO EXTERNAL BLOWS - STAIRCASE METHOD (ISO 11173:1994)
    ISO 3127:1994 Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method
    EN ISO 3451-1:2008 PLASTICS - DETERMINATION OF ASH - PART 1: GENERAL METHODS
    EN ISO 1167-2:2006 (edition 2) Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
    ISO/TR 7620:2005 Rubber materials Chemical resistance
    EN ISO 1167-1 : 2006 THERMOPLASTICS PIPES, FITTINGS AND ASSEMBLIES FOR THE CONVEYANCE OF FLUIDS - DETERMINATION OF THE RESISTANCE TO INTERNAL PRESSURE - PART 1: GENERAL METHOD (ISO 1167-1:2006)
    CEN/TS 15223:2017 PLASTICS PIPING SYSTEMS - VALIDATED DESIGN PARAMETERS OF BURIED THERMOPLASTICS PIPING SYSTEMS
    CEN/TR 1046 : 2013 THERMOPLASTICS PIPING AND DUCTING SYSTEMS - SYSTEMS OUTSIDE BUILDING STRUCTURES FOR THE CONVEYANCE OF WATER OR SEWAGE - PRACTICES FOR UNDERGROUND INSTALLATION
    EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids Dimensions and tolerances Part 1: Metric series
    EN 476:2011 (edition 2) General requirements for components used in drains and sewers
    EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
    ISO 472:2013 Plastics Vocabulary
    EN ISO 9001:2015 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS (ISO 9001:2015)
    EN ISO 3127:2017 THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO EXTERNAL BLOWS - ROUND-THE-CLOCK METHOD (ISO 3127:1994)
    EN 14758-1:2012 (edition 2) Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
    CEN ISO/TR 27165 : 2012 THERMOPLASTICS PIPING SYSTEMS - GUIDANCE FOR DEFINITIONS OF WALL CONSTRUCTIONS FOR PIPES (ISO/TR 27165:2012)
    EN ISO 13967 : 2009 THERMOPLASTICS FITTINGS - DETERMINATION OF RING STIFFNESS
    ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
    EN ISO 9969:2016 THERMOPLASTICS PIPES - DETERMINATION OF RING STIFFNESS (ISO 9969:2016)
    ISO 9001:2015 Quality management systems - Requirements
    EN ISO 580 : 2005 PLASTICS PIPING AND DUCTING SYSTEMS - INJECTION-MOULDED THERMOPLASTICS FITTINGS - METHODS FOR VISUALLY ASSESSING THE EFFECTS OF HEATING
    EN ISO 13254 : 2017 THERMOPLASTICS PIPING SYSTEMS FOR NON-PRESSURE APPLICATIONS - TEST METHOD FOR WATERTIGHTNESS (ISO 13254:2010)
    EN 1401-1:2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
    ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
    ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
    EN ISO 2505 : 2005 THERMOPLASTICS PIPES - LONGITUDINAL REVERSION - TEST METHOD AND PARAMETERS
    ISO 13257:2010 Thermoplastics piping systems for non-pressure applications Test method for resistance to elevated temperature cycling
    ISO/TR 27165:2012 Thermoplastics piping systems - Guidance for definitions of wall constructions for pipes
    EN ISO 13257 : 2017 THERMOPLASTICS PIPING SYSTEMS FOR NON-PRESSURE APPLICATIONS - TEST METHOD FOR RESISTANCE TO ELEVATED TEMPERATURE CYCLING (ISO 13257:2010)
    ISO 13254:2010 Thermoplastics piping systems for non-pressure applications Test method for watertightness
    ISO 13264:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for mechanical strength or flexibility of fabricated fittings
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
    CEN/TS 1852-2:2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    EN ISO 472 : 2013 PLASTICS - VOCABULARY (ISO 472:2013)
    EN 12099:1997 Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
    EN ISO 1183-2:2004 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    ISO 2505:2005 Thermoplastics pipes Longitudinal reversion Test method and parameters
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective