BS EN 573-5:2007
Current
Current
The latest, up-to-date edition.
Aluminium and aluminium alloys. Chemical composition and form of wrought products Codification of standardized wrought products
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
10-31-2007
Publisher
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Codification system
Bibliography
Defines the codification of some standardized semifinished wrought products for use in ordering information.
This document specifies the codification of some standardized semifinished wrought products for use in ordering information. NOTE Codification is usually required for technical drawings. It does not apply to castings, cast forging stock, rolling ingots, extrusion billets and ingots for remelting.
| Committee |
NFE/35
|
| DevelopmentNote |
Supersedes 99/712093 DC. (10/2007)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NBN EN 573-5 : 2008 | Identical |
| DIN EN 573-5:2007-11 | Identical |
| NEN EN 573-5 : 2007 | Identical |
| NS EN 573-5 : 1ED 2007 | Identical |
| I.S. EN 573-5:2007 | Identical |
| EN 573-5:2007 | Identical |
| NF EN 573-5 : 2007 | Identical |
| UNI EN 573-5 : 2007 | Identical |
| SN EN 573-5 : 2007 | Identical |
| EEMUA 105 : 2014 | FACTORY STAIRWAYS, LADDERS AND HANDRAILS (INCLUDING ACCESS PLATFORMS AND RAMPS) |
| BS PD5500(2006) : 2006 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| EN 1715-2:2008 | Aluminium and aluminium alloys - Drawing stock - Part 2: Specific requirements for electrical applications |
| EN 754-3:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form |
| EN 754-7:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form |
| EN 755-5:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 5: Rectangular bars, tolerances on dimensions and form |
| EN 851:2014 | Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications |
| EN 485-3:2003 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products |
| EN 755-9:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form |
| EN 683-3:2006 | Aluminium and aluminium alloys - Finstock - Part 3: Tolerances on dimensions and form |
| EN 485-4:1993 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products |
| EN 755-3:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 3: Round bars, tolerances on dimensions and form |
| EN 755-8:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form |
| EN 1396:2015 | Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications |
| EN 755-4:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 4: Square bars, tolerances on dimensions and form |
| EN 586-3:2001 | Aluminium and aluminium alloys - Forgings - Part 3: Tolerances on dimensions and form |
| EN 755-7:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form |
| EN 12020-2:2016/AC:2017 | ALUMINIUM AND ALUMINIUM ALLOYS - EXTRUDED PRECISION PROFILES IN ALLOYS EN AW-6060 AND EN AW-6063 - PART 2: TOLERANCES ON DIMENSIONS AND FORM |
| EN 1301-3:2008 | Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions |
| EN 754-6:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form |
| EN 755-6:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 6: Hexagonal bars, tolerances on dimensions and form |
| EN 12258-1:2012 | Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms |
| EN 570:2007 | Aluminium and aluminium alloys - Impact extrusion slugs obtained from wrought products - Specification |
| EN 603-3:2000 | Aluminium and aluminium alloys - Wrought forging stock - Part 3: Tolerances on dimensions and form |
| EN 541:2006 | Aluminium and aluminium alloys - Rolled products for cans, closures and lids - Specifications |
| EN 1592-4:1997 | Aluminium and aluminium alloys - HF seam welded tubes - Part 4: Tolerances on dimensions and form for square, rectangular and shaped tubes |
| EN 515:2017 | Aluminium and aluminium alloys - Wrought products - Temper designations |
| EN 941:2014 | Aluminium and aluminium alloys - Circle and circle stock for the production of general applications - Specifications |
| EN 754-5:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 5: Rectangular bars, tolerances on dimensions and form |
| EN 12482-2:1998 | Aluminium and aluminium alloys - Reroll stock for general applications - Part 2: Specifications for cold rolled reroll stock |
| EN 754-8:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form |
| EN 1386:2007 | Aluminium and aluminium alloys - Tread plate - Specifications |
| EN 1715-4:2008 | Aluminium and aluminium alloys - Drawing stock - Part 4: Specific requirements for welding applications |
| EN 12482-1:1998 | Aluminium and aluminium alloys - Reroll stock for general applications - Part 1: Specifications for hot rolled reroll stock |
| EN 1592-3:1997 | Aluminium and aluminium alloys - HF seam welded tubes - Part 3: Tolerances on dimensions and form for circular tubes |
| EN 754-4:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| EN 546-3:2006 | Aluminium and aluminium alloys - Foil - Part 3: Tolerances on dimensions |
| EN 1715-3:2008 | Aluminium and aluminium alloys - Drawing stock - Part 3: Specific requirements for mechanical uses (excluding welding) |
US$160.51
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.