• There are no items in your cart

BS EN 60938-1:2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Fixed inductors for electromagnetic interference suppression Generic specification
Available format(s)

Hardcopy , PDF

Superseded date

10-09-2021

Language(s)

English

Published date

04-30-2007

1 General
    1.1 Scope
    1.2 Normative references
2 Technical data
    2.1 Units and symbols
    2.2 Definitions
    2.3 Preferred values
    2.4 Marking
3 Quality assessment procedures
    3.1 General
    3.2 Primary stage of manufacture
    3.3 Structurally similar inductors
    3.4 Qualification approval procedures
    3.5 Quality conformance inspection
    3.6 Alternative test methods
    3.7 Unchecked parameters
4 Test and measurement procedure
    4.1 General
    4.2 Standard atmospheric conditions
    4.3 Drying
    4.4 Visual examination and check of dimensions
    4.5 Insulation resistance
    4.6 Voltage proof
    4.7 Inductance
    4.8 Insertion loss
    4.9 Robustness of terminations
    4.10 Resistance to soldering heat
    4.11 Solderability (applicable only for
          terminations intended to be soldered)
    4.12 Rapid change of temperature
    4.13 Vibration
    4.14 Bump
    4.15 Shock
    4.16 Container sealing
    4.17 Climatic sequence
    4.18 Damp heat, steady state
    4.19 Temperature rise
    4.20 Endurance
    4.21 Passive flammability
    4.22 Active flammability
    4.23 Solvent resistance of marking
    4.24 Component solvent resistance
Annex A (normative) Interpretation of sampling plans and
         procedures as described in IEC 60410 for use
         within the IEC quality assessment system for
         electronic components (IECQ)
Annex B (normative) Rules for the preparation of detail
         specifications for capacitors and resistors for
         electronic equipment
Annex C (normative) Requirements for earth inductors
Annex ZA (normative) Normative references to international
         publications with their corresponding European
         publications

Applicable to inductors intended for electromagnetic interference suppression meant to be used in or in association with, electronic or electrical equipment and machines. Restricted to inductors where safety tests are appropriate. Also includes two or more inductors within one enclosure.

Committee
W/-
DevelopmentNote
Supersedes BS EN 138000. (03/2000) Supersedes 98/231272 DC. Also numbered as IEC 60938-1. (05/2005)
DocumentType
Standard
Pages
38
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

HD 323.2.20 : 200S3 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST T - SOLDERING
IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
EN 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
IECQ 001002-3:2005 IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 3: APPROVAL PROCEDURES
EN 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-13:1983 Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure
EN 60068-1:2014 Environmental testing - Part 1: General and guidance
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
EN 60068-2-27:2009 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
HD 323.2.3 : 200S2 BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST CA - DAMP HEAT, STEADY STATE
IEC 60068-2-3:1969 Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state
IEC 60294:2012 Measurement of the dimensions of a cylindrical component with axial terminations
EN 60068-2-17:1994 Environmental testing - Part 2: Tests - Test Q: Sealing
IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
EN 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 60062:2016 Marking codes for resistors and capacitors
EN 60062:2016/AC:2016-12 MARKING CODES FOR RESISTORS AND CAPACITORS (IEC 60062:2016/COR1:2016)
EN 60068-2-29:1993 Environmental testing - Part 2: Tests - Test Eb and guidance: Bump
EN 60068-2-13:1999 Environmental testing - Part 2: Tests - Test M: Low air pressure
EN 60068-2-6:2008 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
CISPR 17:2011 Methods of measurement of the suppression characteristics of passive EMC filtering devices
IEC 60068-2-29:1987 Environmental testing. Part 2: Tests. Test Eb and guidance: Bump
EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
EN 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60068-2-45:1992/A1:1993 Environmental testing - Part 2: Tests - Test Xa and guidance: Immersion in cleaning solvents
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60695-2-2:1994/A1:1995 FIRE HAZARD TESTING - TEST METHODS - NEEDLE-FLAME TEST
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

View more information
US$277.90
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.