• There are no items in your cart

BS EN 62196-1:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles General requirements
Available format(s)

Hardcopy , PDF

Superseded date

11-22-2022

Language(s)

English

Published date

01-31-2015

This part of IEC62196 is applicable to plugs, socket-outlets, vehicle connectors, vehicle inlets and cable assemblies for electric vehicles, herein referred to as “accessories??, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding 690V a.c. 50Hz to 60Hz, at a rated current not exceeding 250A, 1500V d.c. at a rated current not exceeding 400A. These accessories are intended to be installed by instructed persons ( IEC60050‑195:1998 , IEC60050‑195/AMD1:2001, 195-04-02) or skilled persons ( IEC60050‑195:1998 , IEC60050‑195/AMD1:2001, 195-04-01) only. These accessories and cable assemblies are intended to be used for circuits specified in IEC61851‑1 which operate at different voltages and frequencies and which may include extra-low voltage and communication signals. These accessories and cable assemblies are to be used at an ambient temperature between -30°C and+50°C. NOTE1 In some countries, other requirements may apply. NOTE2 the following countries, -35°C applies: SE. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this part of IEC62196 are for use in certain modes of charging electric vehicles. These modes are defined in IEC61851‑1 . These definitions and a description of the types of connection (cases A, B and C), are described in IEC61851‑1:2010, 6.2 and 6.3.1. NOTE3 In the following countries, mode 1 will not be allowed: UK, US, CA, SG. This part of IEC62196 does not apply to those standardised accessories used in charging systems where the use of such accessories constructed to the requirements of other standards is permitted (e.g. in mode 1 and mode 2). Such standardized accessories may be used for those situations (mode and case) identified in IEC61851‑1 . This part of IEC62196 may be used as a guide for accessories with a lesser number of contacts and lower ratings for use with light duty vehicles.

Committee
PEL/23/4
DevelopmentNote
Supersedes 01/202446 DC (05/2004). 2003 version remains current. Supersedes 10/30216162 DC. (06/2012) 2012 Edition remains current and will be withdrawn on 15/10/2017. (07/2013) 2012 + A11 2013 Edition remains active & will be withdrawn on 16/06/2017. Supersedes 13/30295015 DC. (10/2014) 2012 + A12 2014 Edition remains active & will be withdrawn on 29/09/2019. Supersedes 13/30277668 DC. (02/2015)
DocumentType
Standard
Pages
92
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
SN EN 62196-1 : 2012 AMD 12 2014 Identical
EN 62196-1:2014 Identical
NF EN 62196-1 : 2015 Identical
NBN EN 62196-1 : 2015 Identical
I.S. EN 62196-1:2014 Identical
DIN EN 62196-1 : 2015 Identical
UNE-EN 62196-1:2015 Identical

IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
EN 60999-2:2003 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm² up to 300 mm² (included)
EN 61851-1:2011 Electric vehicle conductive charging system - Part 1: General requirements
IEC 62752:2016 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)
EN 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
IEC 61540:1997+AMD1:1998 CSV Electrical accessories - Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs)
IEC 60228:2004 Conductors of insulated cables
IEC 60245-6:1994 Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 6: Arc welding electrode cables
EN 61851-23:2014/AC:2016-06 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 23: DC ELECTRIC VEHICLE CHARGING STATION (IEC 61851-23:2014/COR1:2016)
IEC 60309-4:2006+AMD1:2012 CSV Plugs, socket-outlets and couplers for industrial purposes - Part 4: Switched socket-outlets and connectors with or without interlock
EN 60695-10-2:2014 Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method
EN 60309-4:2007/A1:2012 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 4: SWITCHED SOCKET-OUTLETS AND CONNECTORS WITH OR WITHOUT INTERLOCK (IEC 60309-4:2006/A1:2012)
EN 61300-2-6:2011 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism
IEC 60884-1:2002+AMD1:2006+AMD2:2013 CSV Plugs and socket-outlets for household and similar purposes - Part1: General requirements
IEC 60050-441:1984 International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses
IEC 60999-2:2003 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included)
IEC 60269-2:2013+AMD1:2016 CSV Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K
IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part1: General rules
IEC 62335:2008 Circuit breakers - Switched protective earth portable residual current devices for class I and battery powered vehicle applications
IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
EN 60228:2005 COR 2005 CONDUCTORS OF INSULATED CABLES
IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV Low-voltage fuses - Part 1: General requirements
EN ISO 1456:2009 Metallic and other inorganic coatings - Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium (ISO 1456:2009)
EN 60947-1:2007/A2:2014 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014)
ISO 2081:2008 Metallic and other inorganic coatings Electroplated coatings of zinc with supplementary treatments on iron or steel
IEC 61009-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers with integral overcurrentprotection for household and similar uses (RCBOs) - Part 1: General rules
EN 60112 : 2003 AMD 1 2009 METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
IEC 60999-1:1999 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
ISO 1456:2009 Metallic and other inorganic coatings — Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium
EN 61009-1:2012/A12:2016 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITH INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCBOS) - PART 1: GENERAL RULES
IEC TR 60755:2008 General requirements for residual current operated protective devices
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC 60245-4:2011 Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 4: Cords and flexible cables
IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
IEC 61300-2-7:2013 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-7: Tests - Bending moment
EN 62752:2016 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)
ISO 2093:1986 Electroplated coatings of tin — Specification and test methods
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 61300-2-4:1997 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-4: Tests - Fibre/cable retention
HD 193 : 200S2 VOLTAGE BANDS FOR ELECTRICAL INSTALLATIONS OF BUILDINGS
HD 60269-2:2013 Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K
IEC 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
IEC 60664-3:2016 Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
EN 60999-1:2000 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included)
IEC 60695-10-2:2014 Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method
IEC 61300-2-4:1995 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-4: Tests - Fibre/cable retention
EN 61008-1:2012/A12:2017 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITHOUT INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCCBS) - PART 1: GENERAL RULES (IEC 61008-1:2010, MODIFIED)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements
IEC 61300-2-6:2010 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60664-3:2017 Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
EN 61300-2-7:2013 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-7: Tests - Bending moment
IEC 61851-1:2017 Electric vehicle conductive charging system - Part 1: General requirements
EN 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014)
EN 60269-1:2007/A2:2014 LOW-VOLTAGE FUSES - PART 1: GENERAL REQUIREMENTS (IEC 60269-1:2006/A2:2014)
EN 60309-1:1999/A1:2007/AC:2014 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 1: GENERAL REQUIREMENTS (IEC 60309-1:1999/A2:2012)

View more information
US$335.40
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.