Gas cylinders. Refillable seamless steel tubes of water capacity between 150 l and 3000 l. Design, construction and testing

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

02-28-2015

Publisher

British Standards Institution

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Inspection and testing
6 Materials
7 Design
8 Construction and workmanship
9 Type approval procedure
10 Batch tests
11 Tests on every tube
12 Special requirements for tubes for embrittling gases
13 Inspection certificate
14 Marking
Annex A (informative) - Typical chemistry groupings for
        seamless steel tubes
Annex B (normative) - Ultrasonic examination
Annex C (informative) - Description and evaluation of
        manufacturing imperfections and conditions for
        rejection of seamless steel tubes at time of
        final inspection by the manufacturer
Annex D (informative) - Acceptance certificate
Annex E (informative) - Type approval certificate
Annex F (informative) - Bend stress calculation
Bibliography

Describes minimum requirements for the material, design, construction and workman ship, manufacturing processes and tests at manufacture of refillable quenched and tempered seamless steel tubes of water capacities from 150 l up to and including 3000 l for compressed and liquefied gases exposed to extreme world-wide ambient temperatures (normally between -50 degrees C and +65 degrees C).

This International Standard specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examinations and tests at manufacture of refillable quenched and tempered seamless steel tubes of water capacities exceeding 150l up to and including 3000l for compressed and liquefied gases exposed to extreme world-wide ambient temperatures, normally between –50°C and+65°C.

This International Standard is applicable to tubes with a maximum tensile strength, R _ma, of less than 1100MPa. These tubes can be used alone or in batteries to equip trailers or multiple element gas containers (ISO modules or skids) for the transportation and distribution of compressed gases.

This International Standard is applicable to tubes having an opening at each end.

Committee	PVE/3/3
DevelopmentNote	Supersedes 96/705632 DC. (11/2005) Supersedes 11/30237868 DC. (08/2013) Supersedes 09/30143423 DC. (02/2015)
DocumentType	Standard
Pages	44
PublisherName	British Standards Institution
Status	Current
Supersedes	09/30143423 DC : DRAFT MAY 2009 96/705632 DC : APR 96 11/30237868 DC : 0 BS EN ISO 11120:1999+A1:2013

Standards	Relationship
I.S. EN ISO 11120:2015	Identical
DIN EN ISO 11120:2015-05	Identical
UNI EN ISO 11120 : 2013	Identical
NS EN ISO 11120 : 2015	Identical
EN ISO 11120:2015	Identical
NBN EN ISO 11120 : 2015	Identical
UNE-EN ISO 11120:2015	Identical
NF EN ISO 11120 : 2015	Identical
SN EN ISO 11120 : 2015	Identical
NEN EN ISO 11120 : 2015	Identical
ISO 11120:2015	Identical

BS 8562:2011	Gas cylinders. In situ, non-destructive examination and testing of refillable seamless steel tubes of water capacity between 150 L and 3000 L, used for compressed gases Specification
10/30238376 DC : 0	BS 8562 - GAS CYLINDERS IN-SITU EXAMINATION AND TESTING OF REFILLABLE SEAMLESS STEEL TUBES OF WATER CAPACITY BETWEEN 150 L AND 3 000 L, USED FOR COMPRESSED GASES SPECIFICATION

ISO 6506-3:2014	Metallic materials Brinell hardness test Part 3: Calibration of reference blocks
ISO 10893-5:2011	Non-destructive testing of steel tubes Part 5: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections
ISO 6506-1:2014	Metallic materials Brinell hardness test Part 1: Test method
ISO 11114-1:2012	Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
ISO 9712:2012	Non-destructive testing Qualification and certification of NDT personnel
ISO 148-2:2016	Metallic materials — Charpy pendulum impact test — Part 2: Verification of testing machines
ISO 10893-8:2011	Non-destructive testing of steel tubes Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections
ISO 6892-1:2016	Metallic materials Tensile testing Part 1: Method of test at room temperature
ISO 148-1:2016	Metallic materials — Charpy pendulum impact test — Part 1: Test method
ISO 21028-2:2004	Cryogenic vessels Toughness requirements for materials at cryogenic temperature Part 2: Temperatures between -80 degrees C and -20 degrees C
ISO 148-3:2016	Metallic materials — Charpy pendulum impact test — Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines
ISO 11114-4:2017	Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 4: Test methods for selecting steels resistant to hydrogen embrittlement
ISO 6506-2:2017	Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines
ISO 6406:2005	Gas cylinders Seamless steel gas cylinders Periodic inspection and testing
ISO 10893-2:2011	Non-destructive testing of steel tubes Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections
ISO 10893-4:2011	Non-destructive testing of steel tubes Part 4: Liquid penetrant inspection of seamless and welded steel tubes for the detection of surface imperfections
ISO 11117:2008	Gas cylinders Valve protection caps and valve guards Design, construction and tests
ISO 13769:2007	Gas cylinders Stamp marking
ISO 11439:2013	Gas cylinders — High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles

View more information

US$261.13

Excluding Tax where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

BS EN ISO 11120:2015

Current

Table of Contents

Abstract

Scope

General Product Information

International Equivalents

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription