• There are no items in your cart

BS EN ISO 14405-2:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Geometrical product specifications (GPS). Dimensional tolerancing Dimensions other than linear sizes
Available format(s)

Hardcopy , PDF

Superseded date

02-05-2019

Language(s)

English

Published date

12-31-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principles and rules for indication of dimensions and
  related tolerances
5 Units used in drawings for dimensions
6 Indication of tolerances for linear and angular
  dimensions
7 Illustrations of ambiguous +/- tolerancing vs. unambiguous
  geometrical tolerancing
8 Angular tolerancing
Annex A (informative) - Explanations and examples of the
        ambiguity caused by using +/- tolerances for
        dimensions other than linear size
Annex B (informative) - Relation to the GPS matrix model
Bibliography

Depicts the use of geometrical tolerancing for dimensions that are not linear sizes to avoid the ambiguity that the use of +/- tolerances on these dimensions causes.

Committee
TPR/1
DevelopmentNote
Supersedes BS ISO 406. (12/2011)
DocumentType
Standard
Pages
34
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EN ISO 14405-2:2011 Identical
ISO 14405-2:2011 Identical

13/30275718 DC : 0 BS 8888 - TECHNICAL PRODUCT DOCUMENTATION AND SPECIFICATION
16/30334592 DC : 0 BS 8888 - TECHNICAL PRODUCT DOCUMENTATION AND SPECIFICATION
BS 8888:2017 Technical product documentation and specification
BS 8888:2013 Technical product documentation and specification

ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
ISO/TS 17450-2:2002 Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties
ISO 5459:2011 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
ISO 8062-3:2007 Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
ISO 3040:2016 Geometrical product specifications (GPS) Dimensioning and tolerancing Cones
ISO 81714-1:2010 Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules
ISO 2538:1998 Geometrical Product Specifications (GPS) Series of angles and slopes on prisms
ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
ISO 14660-2:1999 Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
ISO/TS 17450-1:2005 Geometrical product specifications (GPS) General concepts Part 1: Model for geometrical specification and verification
ISO 129-1:2004 Technical drawings Indication of dimensions and tolerances Part 1: General principles
ISO 14660-1:1999 Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions
ISO 14405-1:2016 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
ISO 14253-2:2011 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
ISO 13715:2017 Technical product documentation Edges of undefined shape Indication and dimensioning
ISO 5458:1998 Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing
ISO/R 1938:1971 ISO system of limits and fits Part II : Inspection of plain workpieces

View more information
US$261.13
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.