• There are no items in your cart

BS EN ISO 1938-1:2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Geometrical product specifications (GPS). Dimensional measuring equipment Plain limit gauges of linear size
Available format(s)

Hardcopy , PDF

Superseded date

03-21-2019

Language(s)

English

Published date

11-30-2015

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms and symbols
5 Design characteristics for gauges
6 Metrological characteristics
7 Maximum permissible limits on metrological
   characteristics
8 Proving conformance with specification for limit gauges
9 Verification of dimensional specification of a workpiece
   with limit gauges
10 Marking
Annex A (informative) - General principles and application
        of limit gauging
Annex B (informative) - Description of the specific use
        of the various gauge types and the associated
        uncertainty
Annex C (informative) - Relation to the GPS matrix model
Bibliography

Gives the most important metrological and design characteristics of plain limit gauges of linear size.

This part of ISO1938 specifies the most important metrological and design characteristics of plain limit gauges of linear size. This part of ISO1938 defines the different types of plain limit gauges used to verify linear dimensional specifications associated with linear size. This part of ISO1938 also defines the design characteristics and the metrological characteristics for these limit gauges as well as the new or wear limits state Maximum Permissible Limits (MPLs) for the new state or wear limits state for these metrological characteristics. In addition, this part of ISO1938 describes the use of limit gauges. It covers linear sizes up to 500mm.

Committee
TPR/1
DevelopmentNote
Partially supersedes BS 969(2008). Supersedes 11/30231340 DC. (12/2015)
DocumentType
Standard
Pages
42
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EN ISO 1938-1:2015 Identical
ISO 1938-1:2015 Identical

ISO 8015:2011 Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules
ISO 14638:2015 Geometrical product specifications (GPS) Matrix model
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 14978:2006 Geometrical product specifications (GPS) General concepts and requirements for GPS measuring equipment
ISO 1:2016 Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties
ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
ISO 17450-1:2011 Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
ISO/IEC Guide 99:2007 International vocabulary of metrology Basic and general concepts and associated terms (VIM)
ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
ISO 17450-2:2012 Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities
ISO 14405-1:2016 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
ISO 14253-2:2011 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
ISO/R 1938:1971 ISO system of limits and fits Part II : Inspection of plain workpieces
ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)

View more information
US$261.13
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.