• There are no items in your cart

BS ISO 13628-5:2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Petroleum and natural gas industries. Design and operation of subsea production systems Subsea umbilicals
Available format(s)

Hardcopy , PDF

Superseded date

01-31-2010

Language(s)

English

Published date

11-11-2002

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
   3.1 Terms and definitions
   3.2 Abbreviated terms
4 Functional requirements
   4.1 General requirements
   4.2 Project-specific re
5 Quality assurance
6 Design requirements
   6.1 General
   6.2 Design methodology
   6.3 Analysis
7 Component design, manufacture and test
   7.1 General
   7.2 Electric cable
   7.3 Performance requirements - Electric cable
   7.4 Structural analysis - Electric cable
   7.5 Manufacture - Electric cable
   7.6 Verification tests
   7.7 Component acceptance tests - Electric cable
   7.8 Optical fibre cable
   7.9 Hoses
   7.10 Metallic tubes
8 Terminations and ancillary equipment design
   8.1 General
   8.2 Terminations
   8.3 Ancillary equipment
9 Umbilical design
   9.1 Temperature range
   9.2 Maximum working load
   9.3 Minimum breaking load
   9.4 Minimum bend radius
   9.5 Dynamic service life
   9.6 Seabed stability
   9.7 Service environment
   9.8 Cross-sectional arrangement
   9.9 Lay-up
   9.10 Sub-bundles
   9.11 Inner sheath
   9.12 Armouring
   9.13 Outer sheath
   9.14 Length marking
10 Umbilical manufacture and test
   10.1 Umbilical manufacture
   10.2 Verification tests
11 Umbilical factory acceptance tests (FATs)
   11.1 General
   11.2 Visual and dimensional inspection
   11.3 Electric cable
   11.4 Optical fibre cables
   11.5 Hoses
   11.6 Tubes
12 Storage
   12.1 General
   12.2 Protection of umbilical services
   12.3 Spare length
   12.4 Repair kits
   12.5 Handling for integration tests
13 Pre-installation activity
   13.1 Umbilical information
   13.2 Route information
   13.3 Terminations and ancillary equipment information
   13.4 Host facility information
   13.5 Subsea structure information
   13.6 Host facility visit
14 Load-out
   14.1 General
   14.2 Technical audit of load-out facilities
   14.3 Load-out procedure
   14.4 Pre-load-out meetings
   14.5 Pre-load-out tests
   14.6 Load-out operation
   14.7 Stopping and starting the load-out
   14.8 Handling of the umbilical
   14.9 Load-out monitoring
   14.10 Load-out on a reel or carousel
   14.11 Post-load-out tests
15 Installation operations
   15.1 General
   15.2 Requirements for installation vessel and equipment
   15.3 Pre-installation survey
   15.4 I- or J-tube pull-in operations
   15.5 Lay-down of subsea termination (first end)
   15.6 Lay route
   15.7 Handling requirements for the main lay
   15.8 Vessel positioning to achieve required touch-down
   15.9 Control and monitoring of length laid
   15.10 Integrity monitoring during lay
   15.11 Burial operations
   15.12 Approach to subsea termination position (second end)
   15.13 Lay-down of subsea termination
   15.14 Pull-in of subsea termination
   15.15 Pipeline crossings
   15.16 Arming of weak link
   15.17 Post-lay survey
   15.18 Post-burial survey
   15.19 Post-pull-in test
   15.20 Post-hook-up test
   15.21 Retrieval of installation aids
   15.22 Contingencies
   15.23 Repairs
   15.24 Post-installation survey
Annex A (informative) Information to be provided in
        a purchaser's functional specification
Annex B (informative) Umbilical testing
Annex C (informative) Hose and tube preferred sizes
Annex D (normative) Characterization tests for hoses and
        umbilicals
Annex E (informative) Fatigue testing
Bibliography

Defines requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of subsea control systems, chemical injection, gas lift, utility and service umbilicals and associated ancillary equipment for the petroleum and natural gas industries.

Committee
PSE/17/-/4
DevelopmentNote
Supersedes 99/716675 DC (11/2002)
DocumentType
Standard
Pages
114
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 13628-5:2002 Identical
ISO 13628-5:2009 Identical

IEC 60793-1-1 : 2017 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
IEC 60228:2004 Conductors of insulated cables
EN 10257-2:2011 Zinc or zinc alloy coated non-alloy steel wire for armouring either power cables or telecommunication cables - Part 2: Submarine cables
IEC 60502-2:2014 RLV Power cables with extruded insulation and their accessories for rated voltages from 1 kV (<em>U</em><sub>m</sub> = 1,2 kV) up to 30 kV (<em>U</em><sub>m</sub> = 36 kV) – Part 2: Cables for rated voltages from 6 kV (<em>U</em><sub>m</sub> = 7,2 kV) up to 30 kV (<em>U</em><sub>m</sub> = 36 kV)
ASME PV CODE 9 : 2017 BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS
ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
ISO 6801:1983 Rubber or plastics hoses Determination of volumetric expansion
IEC 60793-2:2015 Optical fibres - Part 2: Product specifications - General
ASTM E 562 : 2011 : REDLINE Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count
ISO 14732:2013 Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials
IEC 60502-1:2004+AMD1:2009 CSV Power cables with extruded insulation and their accessories for rated voltages from 1 kV (<em>U</em><sub>m</sub> = 1,2 kV) up to 30 kV(<em>U</em><sub>m</sub> = 36 kV) - Part 1: Cables for rated voltages of 1 kV (<em>U</em><sub>m</sub> = 1,2 kV) and 3 kV (<em>U</em><sub>m</sub> = 3,6 kV)
ISO 4672:1997 Rubber and plastics hoses Sub-ambient temperature flexibility tests
IEC 60794-1-2:2017 Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance
ASME B31.3:2016 PROCESS PIPING
IEC 60794-1-1:2015 Optical fibre cables - Part 1-1: Generic specification - General
ISO 8308:2015 Rubber and plastics hoses and tubing Determination of transmission of liquids through hose and tubing walls
ASME PV CODE 5 : 2017 BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION
ISO 7751:2016 Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to maximum working pressure
API SPEC 17E : 2017 SPECIFICATION FOR SUBSEA UMBILICALS
ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
ISO 4080:2009 Rubber and plastics hoses and hose assemblies Determination of permeability to gas
ISO 6803:2017 Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
API RP 17I : 1996 INSTALLATION GUIDELINES FOR SUBSEA UMBILICALS

View more information
US$356.96
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.