• There are no items in your cart

BS ISO 17165-1:2007

Current
Current

The latest, up-to-date edition.

Hydraulic fluid power. Hose assemblies Dimensions and requirements
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

11-30-2007

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Hose types, nominal inside diameters and maximum
   working pressures, and correspondence of hose
   sizes to tube sizes
6 Dimensions of hose and hose fittings
7 Overview of hose type, type of hydraulic fluid and
   temperature range
8 Summary of hose fitting end forms and key dimensions
9 Requirements for manufacturing instructions for hose
   assemblies
10 Tolerances on hose assembly length and rotational angle
11 Pressure drop of hose assemblies
12 Requirements and tests
13 Marking
14 Identification statement (reference to this part of
   ISO 17165)
Annex A (informative) - Maximum working pressures of hoses
Annex B (informative) - Dimensions of steel tubes to be used in
        combination with hose types listed in Table A.1
Annex C (informative) - Key dimensions of the hose types covered
        in ISO 17165-1
Bibliography

Describes requirements for hose assemblies that are manufactured from hoses that conform to ISO 3949 and to all parts of ISO 1436, ISO 3862, ISO 4079 and ISO 11237 and hose fittings with elastomeric seals that conform to ISO 12151-1, ISO 12151-2, ISO 12151-3 and ISO 12151-6.

This part of ISO17165 specifies requirements for hose assemblies that are manufactured from hoses that conform to ISO3949 and to all parts of ISO1436, ISO3862, ISO4079 and ISO11237 and hose fittings with elastomeric seals that conform to ISO12151-1, ISO12151-2, ISO12151-3 and ISO12151-6.

This part of ISO17165 contains information of the most important criteria for the selection of preferred types of hoses and hose fittings with elastomeric sealing for use in hydraulic fluid power applications.

Recommendations for installation, storage, life cycle and the necessary inspections to ensure the full functionality of hose assemblies are given in ISO/TR17165-2.

Committee
MCE/18/-/4
DevelopmentNote
Supersedes 06/30127099 DC. (11/2007)
DocumentType
Standard
Pages
34
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
ISO 17165-1:2007 Identical

ISO 4079-1:2001 Rubber hoses and hose assemblies Textile-reinforced hydraulic types Specification Part 1: Oil-based fluid applications
ISO 8030:2014 Rubber and plastics hoses — Method of test for flammability
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
ISO 7662:1988 Rubber and plastics hoses — Determination of abrasion of lining
ISO 3949:2009 Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification
ISO 5598:2008 Fluid power systems and components Vocabulary
ISO 6801:1983 Rubber or plastics hoses Determination of volumetric expansion
ISO 4413:2010 Hydraulic fluid power General rules and safety requirements for systems and their components
ISO 12151-2:2003 Connections for hydraulic fluid power and general use — Hose fittings — Part 2: Hose fittings with ISO 8434-1 and ISO 8434-4 24 degree cone connector ends with O-rings
ISO 4672:1997 Rubber and plastics hoses Sub-ambient temperature flexibility tests
ISO 11237-2:2006 Rubber hoses and hose assemblies Wire-braid-reinforced compact types for hydraulic applications Specification Part 2: Water-based fluid applications
ISO/TR 8354:1987 Rubber hoses and hose assemblies for underground mining Textile-reinforced air and water type
ISO 7233:2016 Rubber and plastics hoses and hose assemblies Determination of resistance to vacuum
ISO 4079-2:2005 Rubber hoses and hose assemblies Textile-reinforced hydraulic types Specification Part 2: Water-based fluid applications
ISO 8331:2016 Rubber and plastics hoses and hose assemblies Guidelines for selection, storage, use and maintenance
ISO 7326:2016 Rubber and plastics hoses Assessment of ozone resistance under static conditions
ISO 6162-2:2012 Hydraulic fluid power Flange connections with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76
ISO 8330:2007 Rubber and plastics hoses and hose assemblies Vocabulary
ISO 12151-5:2007 Connections for hydraulic fluid power and general use — Hose fittings — Part 5: Hose fittings with ISO 8434-2 37 degree flared ends
ISO 10960:1994 Rubber and plastics hoses Assessment of ozone resistance under dynamic conditions
ISO 1436-1:2001 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 1: Oil-based fluid applications
ISO 1436-2:2005 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 2: Water-based fluid applications
ISO 12151-3:2010 Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
ISO 6802:2005 Rubber and plastics hoses and hose assemblies with wire reinforcements Hydraulic impulse test with flexing
ISO 8434-3:2005 Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors
ISO 6162-1:2012 Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127
ISO 3862-2:2005 Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types Specification Part 2: Water-based fluid applications
ISO 8580:1987 Rubber and plastics hoses Determination of ultra-violet resistance under static conditions
ISO 8434-6:2009 Metallic tube connections for fluid power and general use — Part 6: 60 degree cone connectors with or without O-ring
ISO 8032:1997 Rubber and plastics hose assemblies Flexing combined with hydraulic impulse test (half-omega test)
ISO 7751:2016 Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to maximum working pressure
ISO/TR 17165-2:2006 Hydraulic fluid power Hose assemblies Part 2: Recommended practices for hydraulic hose assemblies
ISO 12151-1:2010 Connections for hydraulic fluid power and general use — Hose fittings — Part 1: Hose fittings with ISO 8434-3 O-ring face seal ends
ISO 10763:1994 Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures
ISO 4671:2007 Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
ISO 4080:2009 Rubber and plastics hoses and hose assemblies Determination of permeability to gas
ISO 6803:2017 Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
ISO 12151-4:2007 Connections for hydraulic fluid power and general use Hose fittings Part 4: Hose fittings with ISO 6149 metric stud ends
ISO 3862-1:2001 Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types Specification Part 1: Oil-based fluid applications
ISO 11237-1:2004 Rubber hoses and hose assemblies Wire-braid-reinforced compact types for hydraulic applications Specification Part 1: Oil-based fluid applications
ISO 8033:2016 Rubber and plastics hoses Determination of adhesion between components
ISO 8031:2009 Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity
ISO 6743-4:2015 Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems)

View more information
US$277.90
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.