• There are no items in your cart

PD CEN/TS 12201-7:2014

Current
Current

The latest, up-to-date edition.

Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE) Guidance for the assessment of conformity
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

03-31-2014

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms
5 General
6 Testing and inspection
Annex A (normative) - Change of compound
Annex B (normative) - Testing and inspection
        of fabricated fittings
Annex C (informative) - Basic test matrix for
        PE water compounds and piping products
Bibliography

Provides guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 12201 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.

This part of EN 12201 gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 12201 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures. It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1]. NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN ISO/IEC 17065 [5], EN ISO/IEC 17021 [3] or EN ISO/IEC 17020 [2], as applicable. In conjunction with Parts 1 to 5 of EN 12201 (see Foreword) this document is applicable to polyethylene (PE) plastics piping systems for water supply, and for drainage and sewerage under pressure. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions: allowable operating pressure, PFA, up to 25 bar1); an operating temperature of 20 °C as a reference temperature; buried in the ground; sea outfalls; laid in water; above ground, including pipes suspended below bridges. NOTE 2 For applications operating at constant temperature greater than 20 °C and up to 40 °C, see EN 12201-1:2011, Annex A. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.

Committee
PRI/88/2
DevelopmentNote
Supersedes DD CEN/TS 12201-7 and DD CEN/TS 13244-7. (03/2014)
DocumentType
Standard
Pages
44
PublisherName
British Standards Institution
Status
Current
Supersedes
UnderRevision

Standards Relationship
CEN/TS 12201-7:2014 Identical

ISO/IEC 17065:2012 Conformity assessment — Requirements for bodies certifying products, processes and services
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
EN ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
ISO/IEC 17021:2011 Conformity assessment Requirements for bodies providing audit and certification of management systems
EN 12201-4:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
ISO 21751:2011 Plastics pipes and fittings — Decohesion test of electrofusion assemblies — Strip-bend test
EN 12201-3:2011+A1:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings
ISO/TS 19911:2010 Plastics pipes and fittings — Format of a technical file for characterizing PE spigot end fittings
ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
EN ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477:2008)
EN ISO 6259-1:2015 Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015)
EN ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007)
ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
ISO/IEC 17020:2012 Conformity assessment — Requirements for the operation of various types of bodies performing inspection
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 14236:2000 Plastics pipes and fittings Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
EN 12201-5:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN ISO/IEC 17065:2012 Conformity assessment - Requirements for bodies certifying products, processes and services (ISO/IEC 17065:2012)
ISO 9001:2015 Quality management systems — Requirements
EN 12201-2:2011+A1:2013 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
EN ISO/IEC 17021:2011 Conformity assessment - Requirements for bodies providing audit and certification of management systems (ISO/IEC 17021:2011)
EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
EN ISO/IEC 17020:2012 Conformity assessment - Requirements for the operation of various types of bodies performing inspection (ISO/IEC 17020:2012)

View more information
US$261.13
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.