• There are no items in your cart

BS QC 960000:1992

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Generic specification
Available format(s)

Hardcopy , PDF

Superseded date

02-28-2010

Language(s)

English

Published date

10-15-1992

Committees responsible
National foreword
Introduction
Section 1. Scope and object
1.1 Scope
1.2 Object
Section 2. General
2.1 Related publications
2.2 Units and symbols
2.3 Terminology
2.4 Preferred values
2.5 Marking
Section 3. Quality assessment procedures
3.1 Qualification approval/Quality assessment systems
3.2 Primary stage of manufacture
3.3 Structurally similar switches
3.4 Qualification approval procedures
3.5 Quality conformance inspection
3.6 Alternative test methods
3.7 Unchecked parameters
Section 4. Test and measurement procedures
4.1 General
4.2 Standard atmospheric conditions
4.3 General examination
4.4 Resistance measurements
4.5 Voltage stress
4.6 Temperature rise
4.7 Dynamic stress
4.8 Mechanical strength
4.9 Mechanical endurance
4.10 Electrical endurance
4.11 Overload
4.12 Environmental
4.13 Soldering
4.14 Panel seal
4.15 Enclosure seal
4.16 Fluid resistance
4.17 Fire hazard
4.18 Capacitance
4.19 Illumination
Figures
1. Contact bounce test circuit
2. Typical trace of contact bounce
3. Application of forces and torques for test 4.8.1
4. Submersion seal test enclosure

Establishes a uniform quality assessment system and provides consistency by specifying terminology, symbols, test methods and other necessary information.

Committee
EPL/48
DevelopmentNote
Supersedes 84/20971 DC (08/2005)
DocumentType
Standard
Pages
34
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

BS QC 960401:1992 Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for pushbutton switches
BS QC 960100:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for rotary switches
BS QC 960200:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for lever (toggle) switches
BS QC 960400:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for pushbutton switches
BS QC 960301:1992 Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for sensitive switches
BS QC 960201:1992 Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for lever (toggle) switches
BS QC 960300:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for sensitive switches
BS QC 960500:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for in-line package switches

BS 5772-8:1985 Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Connector tests (mechanical) and mechanical tests on contacts and terminations
BS 4500-1.1(1990) : AMD 7630 ISO LIMITS AND FITS - GENERAL, TOLERANCES AND DEVIATIONS - SPECIFICATION FOR BASES OF TOLERANCES, DEVIATIONS AND FITS
BS 5772-4:1979 Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Dynamic stress tests
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
BS 6001-1:1991 Sampling procedures for inspection by attributes Specification for sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection
IEC 60512-7:1993 Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 7: Mechanical operating tests and sealing tests
BS 2011-2.1XA(1981) : 1981 AMD 7553 ENVIRONMENTAL TESTING - TESTS - TEST XA AND GUIDANCE - IMMERSION IN CLEANING SOLVENTS
BS 4727-1:GRP13(1991) : 1991 GLOSSARY OF ELECTROTECHNICAL, POWER, TELECOMMUNICATION, ELECTRONICS, LIGHTING AND COLOUR TERMS - TERMS COMMON TO POWER, TELECOMMUNICATIONS AND ELECTRONICS - ELECTROMECHANICAL COMPONENTS FOR ELECTRONIC EQUIPMENT
BS 4727-2:GRP06(1985) : 1985 GLOSSARY OF ELECTROTECHNICAL POWER TELECOMMUNICATION ELECTRONICS LIGHTING AND COLOUR TERMS - TERMS PARTICULAR TO POWER ENGINEERING - SWITCHGEAR & CONTROLGEAR TERMINOLOGY INCLUDING FUSE TERMINOLOGY
BS 2011-2.1Z/AD:1977 Environmental testing. Tests Tests Z/AD. Composite temperature/humidity cyclic test
IEC 60068-2-38:2009 Environmental testing - Part 2-38: Tests - Test Z/AD: Composite temperature/humidity cyclic test
BS 6334:1983 Methods of test for the determination of the flammability of solid electrical insulating materials when exposed to an igniting source
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
BS QC 001002:1991 Rules of procedure of the IEC quality assessment system for electronic components (IECQ)
BS 5555:1981 Specification for SI units and recommendations for the use of their multiples and of certain other units
BS 5772-3:1979 Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Current-carrying capacity tests
PD 6499:1981 Guide to insulation co-ordination within low-voltage systems including clearances and creepage distances for equipment
BS 2011-2.1T:1981 Environmental testing. Tests Test T. Soldering

View more information
US$277.90
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.