|
IEC 60243-1:2013
|
Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
|
|
IEC 60112:2003+AMD1:2009 CSV
|
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
|
|
IEC 60270:2000+AMD1:2015 CSV
|
High-voltage test techniques - Partial discharge measurements
|
|
EN 60544-1:2013
|
Electrical insulating materials - Determination of the effects of ionizing radiation - Part 1: Radiation interaction and dosimetry
|
|
IEC 60811-3-1:1985
|
Common test methods for insulating and sheathing materials ofelectric cables - Part 3: Methods specific to PVC compounds -Section One: Pressure test at high temperature - Tests forresistance to cracking
|
|
IEC 60212:2010
|
Standard conditions for use prior to and during the testing of solid electrical insulating materials
|
|
IEC 60664-4:2005
|
Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress
|
|
IEC 60068-1:2013
|
Environmental testing - Part 1: General and guidance
|
|
IEC 60068-2-27:2008
|
Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
|
|
IEC 60371-2:2004
|
Specification for insulating materials based on mica - Part 2: Methods of test
|
|
IEC TS 61251:2008
|
Electrical insulating materials - A.C. voltage endurance evaluation - Introduction
|
|
IEC 60050-212:2010
|
International Electrotechnical Vocabulary (IEV) - Part 212: Electrical insulating solids, liquids and gases
|
|
ISO 1663:2007
|
Rigid cellular plastics — Determination of water vapour transmission properties
|
|
ISO/TR 7620:2005
|
Rubber materials — Chemical resistance
|
|
IEC 60493-1:2011
|
Guide for the statistical analysis of ageing test data - Part 1: Methods based on mean values of normally distributed test results
|
|
ISO 9352:2012
|
Plastics — Determination of resistance to wear by abrasive wheels
|
|
IEC 60216-2:2005
|
Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria
|
|
EN 60216-3:2006
|
ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 3: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS
|
|
ISO 877-1:2009
|
Plastics — Methods of exposure to solar radiation — Part 1: General guidance
|
|
IEC 60243-3:2013
|
Electric strength of insulating materials - Test methods - Part 3: Additional requirements for 1,2/50 µs impulse tests
|
|
EN 60216-2:2005
|
Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria
|
|
IEC 60544-1:2013
|
Electrical insulating materials - Determination of the effects of ionizing radiation - Part 1: Radiation interaction and dosimetry
|
|
ISO 1431-1:2012
|
Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing
|
|
ISO 4611:2010
|
Plastics Determination of the effects of exposure to damp heat, water spray and salt mist
|
|
IEC 60068-2-10:2005
|
Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth
|
|
ISO 175:2010
|
Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
|
|
EN 60216-5:2008
|
Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material
|
|
IEC 60068-2-2:2007
|
Environmental testing - Part 2-2: Tests - Test B: Dry heat
|
|
ISO 62:2008
|
Plastics Determination of water absorption
|
|
ISO 877-2:2009
|
Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure behind window glass
|
|
IEC 62231:2006
|
Composite station post insulators for substations with a.c. voltages greater than 1 000 V up to 245 kV - Definitions, test methods and acceptance criteria
|
|
IEC 60243-2:2013
|
Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage
|
|
IEC 60587:2007
|
Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion
|
|
IEC 60068-2-1:2007
|
Environmental testing - Part 2-1: Tests - Test A: Cold
|
|
IEC 60216-5:2008
|
Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material
|
|
IEC 60068-2-14:2009
|
Environmental testing - Part 2-14: Tests - Test N: Change of temperature
|
|
IEC 62539:2007
|
Guide for the statistical analysis of electrical insulation breakdown data
|
|
IEC 61033:1991
|
Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate
|
|
IEC 60216-1:2013
|
Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results
|
|
IEC 61710:2013
|
Power law model - Goodness-of-fit tests and estimation methods
|
|
IEC 60216-3:2006
|
Electrical insulating materials - Thermal endurance properties - Part 3: Instructions for calculating thermal endurance characteristics
|
|
IEC TR 62039:2007
|
Selection guide for polymeric materials for outdoor use under HV stress
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.