IEC GUIDE 109:2012
|
Environmental aspects - Inclusion in electrotechnical product standards
|
EN 60999-2:2003
|
Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm² up to 300 mm² (included)
|
IEC 61076-1:2006
|
Connectors for electronic equipment - Product requirements - Part 1: Generic specification
|
IEC 61984:2008
|
Connectors - Safety requirements and tests
|
IEC 60068-1:2013
|
Environmental testing - Part 1: General and guidance
|
EN 60512-1-100:2012
|
Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
|
EN ISO 1302 : 2002
|
GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INDICATION OF SURFACE TEXTURE IN TECHNICAL PRODUCT DOCUMENTATION (ISO 1302:2002)
|
EN 60068-1:2014
|
Environmental testing - Part 1: General and guidance
|
ISO 11469:2016
|
Plastics — Generic identification and marking of plastics products
|
IEC 60999-2:2003
|
Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included)
|
EN ISO 11469:2016
|
Plastics - Generic identification and marking of plastics products (ISO 11469:2016)
|
EN 61076-1:2006
|
Connectors for electronic equipment - Product requirements - Part 1: Generic specification
|
IEC 60999-1:1999
|
Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
|
ISO 1302:2002
|
Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
|
EN 60512-1-2:2002
|
Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
|
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code)
|
IEC 60512-1-100:2012
|
Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
|
EN 62197-1 : 2006
|
CONNECTORS FOR ELECTRONIC EQUIPMENT - QUALITY ASSESSMENT REQUIREMENTS - PART 1: GENERIC SPECIFICATION
|
EN 60999-1:2000
|
Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included)
|
IEC 62197-1:2006
|
Connectors for electronic equipment - Quality assessment requirements - Part 1: Generic specification
|
EN 61984:2009
|
Connectors - Safety requirements and tests
|
EN 60529:1991/AC:2016-12
|
DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
|
IEC 60068-2-14:2009
|
Environmental testing - Part 2-14: Tests - Test N: Change of temperature
|
IEC 60664-1:2007
|
Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
|
IEC 60050-581:2008
|
International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
|
IEC 60512-1-2:2002
|
Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
|
IEC GUIDE 114:2005
|
Environmentally conscious design - Integrating environmental aspects into design and development of electrotechnical products
|
IEC 60068-2-30:2005
|
Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
|