• There are no items in your cart

CSA C22.2 No. 60950-1 : 2007 : INC : AMD 1 : 2011 : R2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS
Available format(s)

Hardcopy , PDF

Superseded date

09-24-2020

Language(s)

English, French

Published date

01-01-2016

PREFACE
FOREWORD
INTRODUCTION
0 Principles of safety
1 General
2 Protection from hazards
3 Wiring, connections and supply
4 Physical requirements
5 Electrical requirements and simulated abnormal conditions
6 Connection to telecommunication networks
7 Connection to cable distribution systems
Annex A (normative) - Tests for resistance to heat and fire
Annex B (normative) - Motor tests under abnormal conditions
Annex C (normative) - Transformers
Annex D (normative) - Measuring instruments for touch-current
        tests
Annex E (normative) - Temperature rise of a winding
Annex F (normative) - Measurement of clearances and creepage
        distances
Annex G (normative) - Alternative method for determining minimum
        clearances
Annex H (normative) - Ionizing radiation
Annex J (normative) - Table of electrochemical potentials
Annex K (normative) - Thermal controls
Annex L (normative) - Normal load conditions for some types of
        electrical business equipment
Annex M (normative) - Criteria for telephone ringing and other
        signals
Annex N (normative) - Impulse test generators
Annex P (normative) - Normative references
Annex Q (normative) - Voltage dependent resistors (VDRs)
Annex R (informative) - Examples of requirements for quality
        control programmes
Annex S (informative) - Procedure for impulse testing
Annex T (informative) - Guidance on protection against ingress
        of water
Annex U (normative) - Insulated winding wires for use without
        interleaved insulation
Annex V (normative) - A.C. power distribution systems
Annex W (informative) - Summation of touch currents
Annex X (informative) - Maximum heating effect in transformer
        tests
Annex Y (normative) - Ultraviolet light conditioning test
Annex Z (informative) - Overvoltage categories
Annex AA (normative) - Mandrel test
Annex BB (informative) - Changes in the second edition
Annex CC (normative) - Evaluation of integrated circuit (IC)
         current limiters
Annex DD (normative) - Requirements for the mounting means
         of rack-mounted equipment
Annex EE (normative) - Household and home/office document/media
         shredders
Bibliography
Annex NAA (normative) - Markings and instructions
Annex NAB (informative) - D.C. powered equipment and
          centralized d.c. power systems
Annex NAC (normative) - Power line crosses
Annex NAD (normative) - Acoustic tests
Annex NAE (informative) - U.S. and Canadian regulatory
          requirements
INDEX

Pertains to mains-powered or battery-powered information technology equipment, including electrical business equipment and associated equipment, with a RATED VOLTAGE not exceeding 600 V and designed to be installed in accordance with the Canadian Electrical Code, Part I, CSA C22.1-12; General Requirements - Canadian Electrical Code, Part II, CSA C22.2 No. 0-10; the National Electrical Code, NFPA 70-2014; and the National Electrical Safety Code, IEEE C2-2012.

DevelopmentNote
Also numbered as UL 60950-1. Supersedes CSA C22.2.60950. (04/2003) Amendment 1 is available separately, see CSA C22.2.60950-1A. (01/2012) Amendment 2 is available separately, see CSA C22.2.60950-1B. (10/2014)
DocumentType
Standard
Pages
800
ProductNote
Reconfirmed EN
PublisherName
Canadian Standards Association
Status
Superseded
SupersededBy
Supersedes

IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
IEC 60695-11-4:2011 Fire hazard testing - Part 11-4: Test flames - 50 W flame - Apparatus and confirmational test method
IEC 60728-11:2016 Cable networks for television signals, sound signals and interactive services - Part 11: Safety
IEC 61643-321:2001 Components for low-voltage surge protective devices - Part 321: Specifications for avalanche breakdown diode (ABD)
IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS)
IEC 60998-1:2002 Connecting devices for low-voltage circuits for household and similar purposes - Part 1: General requirements
IEC 60664-4:2005 Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress
IEC 60384-14:2013+AMD1:2016 CSV Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
UL 50:13ED 2015-10 Enclosures for Electrical Equipment, Non-Environmental Considerations
NFPA 75 : 2017 FIRE PROTECTION OF INFORMATION TECHNOLOGY EQUIPMENT
IEEE 487-2015 IEEE Standard for the Electrical Protection of Communications Facilities Serving Electric Supply Locations -- General Considerations
C22.1-15 Canadian Electrical Code, Part I (23rd Edition), Safety Standard for Electrical Installations
IEC GUIDE 112:2017 Guide on the safety of multimedia equipment
IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
UL 1863:4ED 2004-05 Standard for Communications-Circuit Accessories
IEC 60073:2002 Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators
CSA C22.2 No. 0.4 : 2004(R2013) BONDING OF ELECTRICAL EQUIPMENT
BS 1363-2(1995) : 1995 13 A PLUGS, SOCKET-OUTLETS, ADAPTORS AND CONNECTION UNITS - PART 2: SPECIFICATION FOR 13 A SWITCHED AND UNSWITCHED SOCKET-OUTLETS
ISO 9773:1998 Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source
IEC TR 62102:2005 Electrical safety - Classification of interfaces for equipment to be connected to information and communications technology networks
IEC 60999-2:2003 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included)
IEC 60050-212:2010 International Electrotechnical Vocabulary (IEV) - Part 212: Electrical insulating solids, liquids and gases
IEC 60896-21:2004 Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test
EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
CFR 21(PTS800-1299) : 0 FOOD AND DRUGS - FOOD AND DRUG ADMINISTRATION, CHAPTER 1 DEPARTMENT OF HEALTH AND HUMAN SERVICES - PARTS 800-1299
ISO 8256:2004 Plastics — Determination of tensile-impact strength
IEC 60885-1:1987 Electrical test methods for electric cables. Part 1: Electrical tests for cables, cords and wires for voltages up to and including 450/750 V
IEC 60825-12:2004 Safety of laser products - Part 12: Safety of free space optical communication systems used for transmission of information
IEC 60227-2:1997+AMD1:2003 CSV Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 2: Test methods
IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
CSA C22.2 No. 31 : 2014 SWITCHGEAR ASSEMBLIES
CFR 47(PTS40-69) : OCT 2017 TELECOMMUNICATIONS - FEDERAL COMMUNICATIONS COMMISSION
IEC 60127-1:2006+AMD1:2011+AMD2:2015 CSV Miniature fuses - Part 1: Definitions for miniature fuses andgeneral requirements for miniature fuse-links
IEC 60269-2-1:2004 Low-voltage fuses - Part 2-1: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Sections I to VI: Examples of types of standardized fuses
IEC 61643-21:2000+AMD1:2008+AMD2:2012 CSV Low voltage surge protective devices - Part 21: Surge protective devices connected to telecommunications and signalling networks - Performance requirements and testing methods
IEC 60695-10-3:2016 Fire hazard testing - Part 10-3: Abnormal heat - Mould stress relief distortion test
IEC 60851-6:2012 Winding wires - Test methods - Part 6: Thermal properties
IEC 60851-5:2008+AMD1:2011 CSV Winding wires - Test methods - Part 5: Electrical properties
IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
IEC 61643-311:2013 Components for low-voltage surge protective devices - Part 311: Performance requirements and test circuits for gas discharge tubes (GDT)
IEC 60227-1:2007 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 1: General requirements
IEC 60999-1:1999 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
ISO 262:1998 ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
IEC 61558-1:2017 Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests
ISO 180:2000 Plastics Determination of Izod impact strength
IEEE C2-2017 NATIONAL ELECTRICAL SAFETY CODE (NESC)(R)
IEC 60906-2:2011 IEC system of plugs and socket-outlets for household and similar purposes - Part 2: Plugs and socket-outlets 15 A 125 V a.c. and 20 A 125 V a.c.
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
ISO 9772:2012 Cellular plastics Determination of horizontal burning characteristics of small specimens subjected to a small flame
BS 1363-1(1995) : 1995 13 A PLUGS, SOCKET-OUTLETS, ADAPTORS AND CONNECTION UNITS - PART 1: SPECIFICATION FOR REWIRABLE AND NON-REWIRABLE 13 A FUSED PLUGS
IEC 61058-1:2016 Switches for appliances - Part 1: General requirements
IEC 60896-22:2004 Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements
IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
CSA C22.2 No. 0.15 : 2015 ADHESIVE LABELS
NFPA 70 : 2017 NATIONAL ELECTRICAL CODE
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
EN 50272-2:2001 Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
IEC 61051-2:1991 Varistors for use in electronic equipment - Part 2: Sectional specification for surge suppression varistors
BS 1363-4(1995) : 1995 13 A PLUGS, SOCKET-OUTLETS, ADAPTORS AND CONNECTION UNITS - PART 4: SPECIFICATION FOR 13 A FUSED CONNECTION UNITS SWITCHED AND UNSWITCHED
IEC 60906-1:2009 IEC system of plugs and socket-outlets for household and similar purposes - Part 1: Plugs and socket-outlets 16 A 250 V a.c.
IEC 60851-3:2009+AMD1:2013 CSV Winding wires - Test methods - Part 3: Mechanical properties
ISO 4892-4:2013 Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
IEC 62471:2006 Photobiological safety of lamps and lamp systems
CSA E60825.1 : 2015 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS
IEC TS 60695-11-3:2004 Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test methods
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO 261:1998 ISO general purpose metric screw threads General plan
IEC 61965:2003 Mechanical safety of cathode ray tubes
IEC 61643-331:2003 Components for low-voltage surge protective devices - Part 331: Specification for metal oxide varistors (MOV)
IEC 60747-5-5:2007+AMD1:2013 CSV Semiconductor devices - Discrete devices - Part 5-5: Optoelectronic devices - Photocouplers
IEC 62133 : 2.0EN+(REDLINE+VERSION) SECONDARY CELLS AND BATTERIES CONTAINING ALKALINE OR OTHER NON-ACID ELECTROLYTES - SAFETY REQUIREMENTS FOR PORTABLE SEALED SECONDARY CELLS, AND FOR BATTERIES MADE FROM THEM, FOR USE IN PORTABLE APPLICATIONS
CSA C22.2 No. 226 : 1992 PROTECTORS IN TELECOMMUNICATION NETWORKS
IEC 60695-10-2:2014 Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method
ISO 4046-4:2002 Paper, board, pulps and related terms Vocabulary Part 4: Paper and board grades and converted products
ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
IEC 60317-43:1997+AMD1:2010 CSV Specifications for particular types of winding wires - Part 43: Aromatic polyimide type wrapped round copper wire, class 240
IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
IEC 61032:1997 Protection of persons and equipment by enclosures - Probes for verification
IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
IEC 60695-11-5:2016 Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
AS/NZS 3112:2017 Approval and test specification - Plugs and socket-outlets
ISO 178:2010 Plastics Determination of flexural properties
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
ASTM E 162 : 2016 : REDLINE Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
IEC 62368-1:2014 Audio/video, information and communication technology equipment - Part 1: Safety requirements
IEEE 269-2010 REDLINE IEEE Standard Methods for Measuring Transmission Performance of Analog and Digital Telephone Sets, Handsets, and Headsets
IEC 60990:2016 Methods of measurement of touch current and protective conductor current
CSA C22.2 No. 94.2 : 2015 ENCLOSURES FOR ELECTRICAL EQUIPMENT, ENVIRONMENTAL CONSIDERATIONS
IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements

View more information

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.